=advance engineering sprint car=
-
- Approved Member
- Posts: 3756
- Joined: Tue Feb 07, 2006 2:12 pm
- Has thanked: 18 times
- Been thanked: 36 times
=advance engineering sprint car=
heya folks!!
this is the build that got me into the vintage rc10.
-advance engineering sprint conversion
-stealth tranny
-robinson racing adj. rear toe kit
-rayborn racing rear sliders
-parma sway bars
-andys f&r arms
-mip steering
-team car front and rear shock towers (rear tower has its mount ears cut off and is just an esc mount now)
-titanium turnbuckles
-tekin g9 supersonic esc
-trinity oval motor
-novak xxl reciever
yadda yadda yadda...
its completely RTR, but will never see any use.
i screwed up on the big wing, (put the big side on backwards) and lost the little wing supports. other than someday fixing that with an all-aluminum wing this puppy is done.
this is the build that got me into the vintage rc10.
-advance engineering sprint conversion
-stealth tranny
-robinson racing adj. rear toe kit
-rayborn racing rear sliders
-parma sway bars
-andys f&r arms
-mip steering
-team car front and rear shock towers (rear tower has its mount ears cut off and is just an esc mount now)
-titanium turnbuckles
-tekin g9 supersonic esc
-trinity oval motor
-novak xxl reciever
yadda yadda yadda...
its completely RTR, but will never see any use.
i screwed up on the big wing, (put the big side on backwards) and lost the little wing supports. other than someday fixing that with an all-aluminum wing this puppy is done.
- Electrohacker
- Approved Member
- Posts: 41
- Joined: Wed Feb 08, 2006 1:53 am
- MelvinsArmy
- Approved Member
- Posts: 3224
- Joined: Tue Feb 07, 2006 10:22 pm
- Location: Des Moines, IA
- Been thanked: 8 times
-
- Approved Member
- Posts: 3756
- Joined: Tue Feb 07, 2006 2:12 pm
- Has thanked: 18 times
- Been thanked: 36 times
thx melvin. its my top shelf queen but if someday 'll definetly run it around a few times and get it dirty. it deserves to be on dirt at least once, i think a baseball diamond would be fun. (prolly tumble the darn thing...)
the advance wheels are really cool. but they dont have a lip on the wheel for a bead, and when i bench tested it they didnt hold very well. but back then i was a newbie, and i prolly used crazy glue.
i kinda want to build another one... a really sinister one.
the advance wheels are really cool. but they dont have a lip on the wheel for a bead, and when i bench tested it they didnt hold very well. but back then i was a newbie, and i prolly used crazy glue.
i kinda want to build another one... a really sinister one.
- Sharkman
- Approved Member
- Posts: 161
- Joined: Fri May 19, 2006 7:53 pm
- Location: 150 miles south of Widdys place
Hoop', Sprinter is too sharp!!
Here's one for you fellas thast might consider a sprint build. http://www.bigboytoys.homestead.com/
The link works,but might try the contact to see if these are still available.
Here's one for you fellas thast might consider a sprint build. http://www.bigboytoys.homestead.com/
The link works,but might try the contact to see if these are still available.
Dan
- MelvinsArmy
- Approved Member
- Posts: 3224
- Joined: Tue Feb 07, 2006 10:22 pm
- Location: Des Moines, IA
- Been thanked: 8 times
-
- Approved Member
- Posts: 3756
- Joined: Tue Feb 07, 2006 2:12 pm
- Has thanked: 18 times
- Been thanked: 36 times
thx dude. i bounce back an forth on polishing everything. yours looks killer all blinged out but i kinda like the satin look. (not to mention its far less work ) dont be a bonehead like me and put the wing together wrong...shodog wrote:Great looking sprinter bad hoopty. Those wheels look killer with the big fat meat tires. I need to get motivated and Finish my sprinter off. Basically I just need to do the body and wing. Scrap, I had the same problem with Big boys toys. I wanted to get some stuff and the e-mails just bounce back.
- shodog
- Approved Member
- Posts: 3816
- Joined: Thu Oct 05, 2006 3:09 pm
- Location: Washington
- Has thanked: 3 times
- Been thanked: 86 times
I have been wanting to make a wing from aluminum but I need to get some good quality stuff that will polish up nicelybadhoopty wrote:thx dude. i bounce back an forth on polishing everything. yours looks killer all blinged out but i kinda like the satin look. (not to mention its far less work ) dont be a bonehead like me and put the wing together wrong...shodog wrote:Great looking sprinter bad hoopty. Those wheels look killer with the big fat meat tires. I need to get motivated and Finish my sprinter off. Basically I just need to do the body and wing. Scrap, I had the same problem with Big boys toys. I wanted to get some stuff and the e-mails just bounce back.
Jim
- Asso_man!
- Approved Member
- Posts: 3959
- Joined: Thu Aug 03, 2006 7:49 am
- Location: EU
- Has thanked: 40 times
- Been thanked: 70 times
something like ordering from Van's Inventscr8p wrote:i've tried e-mailing b.b.t. about the their sprints, and it keeps getting kicked back to me. i've also tried calling with no sucsess, also. so, more or less, you can look at them, but appartently not buy one.
_____________________________________________
_____________________________________________
Come and visit the stable
_____________________________________________
Come and visit the stable
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 30 Replies
- 4921 Views
-
Last post by DennisM
-
- 5 Replies
- 1681 Views
-
Last post by JOESGARAGE
-
- 0 Replies
- 811 Views
-
Last post by scootmike
-
- 0 Replies
- 1321 Views
-
Last post by railey72
-
- 4 Replies
- 1147 Views
-
Last post by PlastiZapCA+
-
- 21 Replies
- 1998 Views
-
Last post by Soncho Ponza
-
- 7 Replies
- 682 Views
-
Last post by njdriver04
-
- 13 Replies
- 3220 Views
-
Last post by marty slater
Who is online
Users browsing this forum: Dual and 14 guests