RPM Narrow Rear End Outer Hinge Pins

Moderators: scr8p, klavy69

2 posts • Page 1 of 1

JOHNBOY74: Approved Member; Posts: 32; Joined: Tue Feb 03, 2015 7:35 pm; Location: Raleigh,NC

RPM Narrow Rear End Outer Hinge Pins

Quote

Post by JOHNBOY74 » Sat Jan 23, 2016 10:18 pm

Does anybody know which outer hinge pins go in the RPM narrow rear end kit. 6381 pins are too long and will hit my wheels if pushed to one side. I have another worlds with the RPM kit and the pins fit flush with the end but it has been years since I built that car and cant remeber which ones I used.

Attachments

scr8p: Administrator; Posts: 16527; Joined: Tue Feb 07, 2006 9:46 pm; Location: Northampton, PA; Has thanked: 28 times; Been thanked: 957 times

Re: RPM Narrow Rear End Outer Hinge Pins

Quote

Post by scr8p » Sun Jan 24, 2016 12:20 am

Truck outers, or just put a spacer on either side to take up the space.

Flashback R/C Products

My Gallery

Post Reply

2 posts • Page 1 of 1

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Sign in

Similar Topics

Replies

Views

Last post

Rear Outer Hinge Pins for RPM A-Arms

Last post by Twistedaxle « Thu Dec 08, 2016 11:58 pm
Posted in RC10 Truck Forum
Replies: 7
by PerryCodes » Fri Dec 02, 2016 10:34 pm » in RC10 Truck Forum

First post

I'm knee deep in a vintage black tub nitro rebuild project and I have arrived at a problem. The RPM A-Arms I'm using seem to be based on the very earliest a-arms for RC10GT. That means the front are the type that require 6471 and the increasingly...

Last post

B2/3 T3 hinge pins fit on the money asc9263

7 Replies

1293 Views

Last post by Twistedaxle
Thu Dec 08, 2016 11:58 pm
RPM Trans with B4 slipper & Front inner hinge pins help

Last post by slow_jun « Tue May 11, 2010 10:45 pm
Posted in Temple's RC10 Tech Forum
Replies: 12
by metallicats33 » Tue Apr 06, 2010 9:54 pm » in Temple's RC10 Tech Forum

First post

Well I'm trying to do a build with nothing but new parts and so far the only part I can't find is # 6226 Front inner hing pins. Are there any other pins out there (associated or not) that are the same?

Also I remember reading here somewhere that...

Last post

thanks metallicats33,

saw the top shaft for RC10, i inspected the Hydra drive kit last night and saw that there were missing screws, will try to look for one in Ebay. I believe there was a rebuild kit for Hydra drive before, is it still available...

12 Replies

982 Views

Last post by slow_jun
Tue May 11, 2010 10:45 pm
Tip for alt parts to replace H-arm, LXT outer hinge and hub

Last post by mytimac « Tue Feb 22, 2011 5:16 pm
Posted in Losi Forum

by mytimac » Tue Feb 22, 2011 5:16 pm » in Losi Forum

I am currently going through all the manuals and explodes for 14 different old models. Trying to make a compatibly chart for parts.
The GTX NXT explodes opened my eyes on an alternate for the H-Arm and LXT arm outer hinge pins a2023. I am sure...

0 Replies

519 Views

Last post by mytimac
Tue Feb 22, 2011 5:16 pm
RPM worlds Rear end question

Last post by JK Racing « Tue Jan 08, 2008 7:02 pm
Posted in Temple's RC10 Tech Forum
Replies: 5
by JK Racing » Tue Jan 08, 2008 1:38 am » in Temple's RC10 Tech Forum

First post

As I plan to race my RC10 with the worlds front/rear conversion kit, the main part I am seriously concerned about are the rear arm mounts. If I bust one, without having some spare vintage parts on hand, what would I use to replace them? RC10GT?...

Last post

The set I've been looking at has both 1 & 3, I figure I would get a couple set of different toe in rear hubs to compensate....

5 Replies

550 Views

Last post by JK Racing
Tue Jan 08, 2008 7:02 pm
RPM TEAM CAR REAR END KIT

Last post by templeofspeed « Thu Oct 11, 2007 6:20 pm
Posted in Temple's RC10 Tech Forum
Replies: 43
by danglenode » Thu Oct 04, 2007 6:50 pm » in Temple's RC10 Tech Forum
1

2

3
First post

HI-

I recently got a hold of some great vintage NIP RC10 Parts and I was wondering in particular about the RPM RC10 Team car Rear End Kit # 7079. I know these are hard to find and I just wanted to check and see what people are using these for and...

Last post

The RPM World's 91 setup moves both the front and rear inner arm pivot points inwards, retaining the same track width. The arms are longer to compensate for moving the front (via a 10T bulkhead and noseplate ) and rear (via narrowing the chassis via...
43 Replies

3858 Views

Last post by templeofspeed
Thu Oct 11, 2007 6:20 pm
Hinge pins

Last post by sandkil « Thu Mar 08, 2018 11:04 am
Posted in R/C Off-Topic / Chit-Chat
Replies: 4
by sandkil » Thu Mar 08, 2018 3:32 am » in R/C Off-Topic / Chit-Chat

First post

I'm searching for a 3.2mm = 0.125 diam hinge pin with a lenght of 1.03
I think that AE 6227 king pin is 1 , but that is a tad too short for my application.

I have in my boxes one hinge pin that meassures 1,03 in legth, but I do not know whats it...

Last post

Ha I found it!

Right before my eyes :roll: It's the outer front B2/B3 hinge pin.

Thanks jwscab!!

4 Replies

1015 Views

Last post by sandkil
Thu Mar 08, 2018 11:04 am
are hinge pins still available???

Last post by PBR Allstar « Sun Jan 18, 2009 1:19 pm
Posted in Temple's RC10 Tech Forum
Replies: 4
by PBR Allstar » Sat Jan 17, 2009 7:56 pm » in Temple's RC10 Tech Forum

First post

I searched the site a bit but didn't find much. I was wondering if stock RC10 hinge pins are available still? I looked on the tower site but didn't find much too explanitory? Any help with part no's or sources would be much appreciated. I just got a...

Last post

thanks temple and scrape, that's exactally what I was hoping for!!!!

4 Replies

689 Views

Last post by PBR Allstar
Sun Jan 18, 2009 1:19 pm
AE Hinge pins

Last post by LoboNYC « Thu Feb 23, 2023 6:00 pm
Posted in 21st Century Modern
Replies: 12
by XLR8 » Wed Feb 22, 2023 11:18 am » in 21st Century Modern

First post

Hey all,
I'm using SC10 caster and steering blocks for a custom build and I'm having some trouble finding hinge pins - or rod material to make them.
Apparently AE changed from 1/8 to 0.110 diameter sometime prior to the B4? Anyway, the set is...

Last post

I agree with the Porsche needing have the engine mounted in the rear. That's why i wanted to slide a DS chassis uunder a Porsche body...for the rear engine handling characteristics.

Now when i did the Pantera DS...i used a mid engine mounted...

12 Replies

754 Views

Last post by LoboNYC
Thu Feb 23, 2023 6:00 pm

Return to “RC10 Buggy Forum”

Who is online

Users browsing this forum: Bing [Bot], Google [Bot] and 17 guests

RPM Narrow Rear End Outer Hinge Pins

RPM Narrow Rear End Outer Hinge Pins

Re: RPM Narrow Rear End Outer Hinge Pins

Create an account or sign in to join the discussion

Create an account

Sign in

Who is online

Login Register