RC10T--racer--4M

[Soncho Ponza]

Had this truck iv been working on for some time. My two boys and i were out running their slashes today jumpn crashn and havn a great time . Dad needs to get a rig to run . i got enough to choose from just none done . The local off road club is about to get the season started and what better reason to get this one finished, and racing [/img][/img][/img]

[PBR Allstar]

Someones been gettin' busy with the G10! Looks really good!

[Soncho Ponza]

I know i love this stuff i can get it cheap. if you mess up a piece your not out much. mostly time

[RER40]

I know i love this stuff i can get it cheap. if you mess up a piece your not out much. mostly time

Some really nice work.
G4 is great to work with, especially when trying to make stuff that always doesn't work out the first time around (cheap to toss and start over). I used to use it first time around, and use the finalized version as a template for the CF version.

[Soncho Ponza]

Heres the look sometimes the paint can be the hardest to decided i toyd with flames tribals drips splats multicolored neon looked all kinds of new looks at the custom paint sites . I can always design a scheme for someone else that i think just looks fantastic but when i sit down for myself i go blank . a buddy said go old look so i pulled out some of the pics of my old rides and this is one i used to run. [/img]

[greazy]

Looks great, nice paint work.

[Twiceblown351]

What body is that. I like it. Very nice job on the paint.

[Soncho Ponza]

ran her on sunday WOOOOW she was fast . TQd but but lost a motor wire while leading main combo too light solder and super hot motor base set up i used worked good then did a little tweekn and lighter oil in back and dialed thinkn bout brushless here is couple action shots[/img][/img]

[Soncho Ponza]

I did a new straighter chassis some suspension work, and a fresh bit of paint for the Hank Perry 240 up in Spokane It has been 20 yrs since i raced there. they had a fresh new track and driver stand. Qualified 6th in the A, and ended up 5th after three mains. Best run was 3rd in the 2nd rnd. Mite have pulled off a 3rd or 4th overall but had some serious dildo turnmarshals and stayd on my lid for half a lap till someone finally looked over and saw me. my set up had too much steering. as I made small changes she got better and better. I started the event by plugging my batt in backwards..pffft i havent done that dumb beaner mistake in a while.

[metallicats33]

Nice work on the race and custom fab parts What body is that on there? looks nice and mean

[SteveK]

That looks awesome. With bracing like that, you could actually do away with the tub and make a chassis out of a narrower strip of G10.

[slotcarrod]

I did a new straighter chassis some suspension work, and a fresh bit of paint for the Hank Perry 240 up in Spokane It has been 20 yrs since i raced there. they had a fresh new track and driver stand. Qualified 6th in the A, and ended up 5th after three mains. Best run was 3rd in the 2nd rnd. Mite have pulled off a 3rd or 4th overall but had some serious dildo turnmarshals and stayd on my lid for half a lap till someone finally looked over and saw me. my set up had too much steering. as I made small changes she got better and better. I started the event by plugging my batt in backwards..pffft i havent done that dumb beaner mistake in a while.

Very nice truck and it looks like it's dialed! I was at that track in Spokane in April and then a week before the Hank, hoping to get in a few laps of practice. Track was still being built both times ,wast of time for me. Seven hour drive with 3 cars and charged lipos. Oh well! Some friends went down from Calgary to the Hank. Mark Huges raced his T4, not sure what class. He may have raced with you!

Can you give us your setup on the 10T? Where you from Sancho?

[Soncho Ponza]

Ontario OR is home base race in boise area. We got a Pro race this weekend. I put in a stock gear box to use the newer slipper. She lacked a little grunt from the RPM i was using. when rolling it would pull the front off the ground with ease. I slide the rear blocks back and had run it that way for awhile. The track was so much diff than i was used to. I spaced the axle forward which put it just back of half way and wrked better. i had lightened oil all around to give a liitle more suspension action. Even though the track was hard packed the 8th scale really tears stuff up. (When I got Home I bought A MBX6) oh back to truck. a few more runs and it would have gotten to a better set. If i can figure how to get the RPM gear on the Newer shaft i think that would be badd A$$. I painted all my rigs back to My 90s color scheme Little bit of accent changes. . Then I painted all my rigs to Match (SC10, Jammin Corr, rc8E and mbx6)...OH YA

[Soncho Ponza]

[/img][/img]

[JK Racing]

would you divulge where you get the G10? if not publicly would you be willing to PM it to me