
What is this belt pulley system for?
- GoMachV
- Approved Member
- Posts: 12157
- Joined: Sun Apr 29, 2012 10:31 pm
- Location: Twin Falls, ID
- Has thanked: 1075 times
- Been thanked: 3688 times
Re: What is this belt pulley system for?
Belt conversion most likely for Stinger mk1. Possibly Optima, but unlikely without revised gearbox and idler.
It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website
Factory Works website
- Asso_man!
- Approved Member
- Posts: 3960
- Joined: Thu Aug 03, 2006 7:49 am
- Location: EU
- Has thanked: 40 times
- Been thanked: 81 times
Re: What is this belt pulley system for?
Nope this is a belt conversion set for the 834B that replaces the chain system (obviously)
_____________________________________________
_____________________________________________
Come and visit the stable
_____________________________________________
Come and visit the stable
- GoMachV
- Approved Member
- Posts: 12157
- Joined: Sun Apr 29, 2012 10:31 pm
- Location: Twin Falls, ID
- Has thanked: 1075 times
- Been thanked: 3688 times
Re: What is this belt pulley system for?
It would be nice to see a measurement, those pullies look too big for the 834b- and they have the 4 screw holes that have the same pattern as a kyosho gear diff
It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website
Factory Works website
-
- Approved Member
- Posts: 404
- Joined: Sun Apr 15, 2012 1:00 pm
- Location: Cardiff, Wales, UK
- Been thanked: 12 times
Re: What is this belt pulley system for?
So, a few of these have been kicking around on eBay and were advertised for a yokomo dogfighter. Excitedly, I bought one but upon arrival I had a good look and I tend to agree with Jeff's comments. The pulleys are a bit big and are reminiscent of optima ones. However, I can't see how the gear would fit properly into the pulleys.
So now I'm less excited...I wanted a belt drive system for an 834b rebuild....
So now I'm less excited...I wanted a belt drive system for an 834b rebuild....
-
- Approved Member
- Posts: 361
- Joined: Wed Nov 12, 2008 9:03 pm
- Location: China
- Been thanked: 1 time
Re: What is this belt pulley system for?
Oh, I lost the bid final seconds, and see it again.I think this is an interested design
- GoMachV
- Approved Member
- Posts: 12157
- Joined: Sun Apr 29, 2012 10:31 pm
- Location: Twin Falls, ID
- Has thanked: 1075 times
- Been thanked: 3688 times
Re: What is this belt pulley system for?
I'm 99% sure it would bolt onto a case half of an optima. You would remove the chain side and leave the gear side intact. Same with stinger. You can see the cross pin fits in the gear side
It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website
Factory Works website
- GoMachV
- Approved Member
- Posts: 12157
- Joined: Sun Apr 29, 2012 10:31 pm
- Location: Twin Falls, ID
- Has thanked: 1075 times
- Been thanked: 3688 times
Re: What is this belt pulley system for?
It would be nice to get a belt measurement, then we could say for sure optima or stinger. The kyosho belt conversion for the stinger lacked a rear trans case, but the optima had one and added a simple pulley to control the belt. Aftermarket may have not deemed it necessary
It's time to stand up to the bully. Support the companies that support the industry, not the ones that tear it down. Say no to Traxxas
Factory Works website
Factory Works website
-
- Regular Member
- Posts: 17
- Joined: Mon Jan 19, 2009 5:39 am
- Location: San Francisco CA.
- Been thanked: 1 time
Re: What is this belt pulley system for?
Hi these are the Cogs for a belt drive 834b I am still looking for the belt for it.
-
- Approved Member
- Posts: 1191
- Joined: Sun Feb 08, 2009 9:20 pm
- Location: Spokane, WA
- Has thanked: 170 times
- Been thanked: 23 times
Re: What is this belt pulley system for?
krate-mayhem wrote:Hi these are the Cogs for a belt drive 834b I am still looking for the belt for it.
Sadly you just missed that belt on Ebay.

-
- Regular Member
- Posts: 17
- Joined: Mon Jan 19, 2009 5:39 am
- Location: San Francisco CA.
- Been thanked: 1 time
Re: What is this belt pulley system for?
Thanks for the info,when I use to race it,it had to much drag so I put the chain and the sprockets back on.
-
- Approved Member
- Posts: 404
- Joined: Sun Apr 15, 2012 1:00 pm
- Location: Cardiff, Wales, UK
- Been thanked: 12 times
Re: What is this belt pulley system for?
I've given up looking for a belt drive system for the time being...I'm just going to keep it stock!
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 0 Replies
- 1682 Views
-
Last post by DTohill
-
- 2 Replies
- 779 Views
-
Last post by shodog
-
- 8 Replies
- 2003 Views
-
Last post by polarbear
-
- 12 Replies
- 2552 Views
-
Last post by RichieRich
-
- 12 Replies
- 2856 Views
-
Last post by stickboy007
-
- 14 Replies
- 2364 Views
-
Last post by isobarik
-
- 1 Replies
- 1057 Views
-
Last post by mk-Zero
-
- 34 Replies
- 3548 Views
-
Last post by treehugger
Who is online
Users browsing this forum: No registered users and 1 guest