Custom Works Enforcer 10

Post by **Brandon G** » Tue Sep 01, 2009 9:01 am

Got this recently off the bay. I have been looking for an old school sprinter to add to my collection... Finally found one for what I thought was reasonable.

Came with all vintage electronics, Novak M something esc, 2 new Reedy Sonic mod motors, a Tekin receiver, Sanyo battery pack, plus lots of tires and parts.

As much as I like the thought of keeping this car new and unused, I plan on running this locally. Can't see spending $400+ for a "newer" version of this car when this will do the job. I will have to do some axle converting in the rear to allow the use of B4 wheels, but that aint anything new...

Post by **Mr. ED** » Tue Sep 01, 2009 3:58 pm

very clean and good-looking. Why do you want to convert the wheels?
If you got a couple tires and wheels with the car, just run these for some time.

Is this the car with the sliding steering components?

Post by **Brandon G** » Tue Sep 01, 2009 4:29 pm

They are the 2.1" rears that were included. I've used 2.2" tires on these wheels once before but didn't like how it turned out. Unfortunately, none of the rubber that came with it would be too effective on the track I will be running at.

And yes, it does have the sliding steering section. Interesting.

Post by **Mr. ED** » Wed Sep 02, 2009 5:40 am

I've been wanting to get that steering setup for a trial on some concept cars. Someone here proposed the idea, but I've been checking regularly on their site and it allways shows as out of stock

Post by **scr8p** » Wed Sep 02, 2009 6:01 am

http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXNTD1&P=SM

nice Enforcer 10 you got there, brandon.

Post by **Mr. ED** » Wed Sep 02, 2009 6:54 am

scr8p wrote:http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXNTD1&P=SM
...

Thanks!!! I've added it to my whishlist, and when I finally have a new job I'll put in the order for all those little things collected in it. there's sooo much little stuff on their site I have ideas for

Post by **Brandon G** » Wed Sep 02, 2009 8:06 am

scr8p wrote:http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXNTD1&P=SM

nice Enforcer 10 you got there, brandon.

Correct you are scr8p. I will fix it!

Post by **scr8p** » Wed Sep 02, 2009 8:10 am

you must've had bolink on your mind.

have fun with it. sprinters are a blast to drive. especially wingless.

Post by **Charlie don't surf** » Wed Sep 02, 2009 8:46 pm

Brandon, any chance you want to sell those front Proline wide 5 front tires? LMK

Reggie

Post by **Brandon G** » Mon Sep 14, 2009 12:53 pm

Already reserved for my '94 worlds car...

Post by **Charlie don't surf** » Mon Sep 14, 2009 3:40 pm

Smart man

Post by **Brandon G** » Fri Nov 13, 2009 3:04 pm

Work has finally begun on this car!

I have done the rear arm conversion similar to my '91 worlds car. RPM RC10GT rear hubs, Dynotech "Klein" rear arms, MIP B4 CVD's.

The front has been widened with the Dynotech wide Enforcer 10 arms.
Running B4 wheels front and rear.

Waiting to paint my 7"X7" Custom works top wing.

Novak GTB and 13.5 BL motor is on the way...

Post by **Mr. ED** » Fri Nov 13, 2009 3:06 pm

been holding my laptop in different angles but can't get a clear view on that steering system

Post by **scr8p** » Fri Nov 13, 2009 7:00 pm

Mr. ED wrote:been holding my laptop in different angles but can't get a clear view on that steering system

the custom works slider bellcrank.

Post by **Mr. ED** » Sun Nov 15, 2009 10:26 am

I know, just wanted to see it mounted. Still haven't pulled my finger out to order one of those for my custom projects

RC10Talk - The Net's Largest Vintage R/C Community

Custom Works Enforcer 10

Custom Works Enforcer 10

Re: Custom Works Eliminator 10

Re: Custom Works Eliminator 10

Re: Custom Works Eliminator 10

Re: Custom Works Eliminator 10

Re: Custom Works Eliminator 10

Re: Custom Works Eliminator 10

Re: Custom Works Enforcer 10

Re: Custom Works Enforcer 10

Re: Custom Works Enforcer 10

Re: Custom Works Enforcer 10

Re: Custom Works Enforcer 10

Re: Custom Works Enforcer 10

Re: Custom Works Enforcer 10

Re: Custom Works Enforcer 10

Create an account or sign in to join the discussion

Create an account

Sign in

Who is online