Hirobo Bearcat SS - Let's start something else...
- silvertriple
- Super Member
- Posts: 1671
- Joined: Sun May 02, 2021 10:31 am
- Location: France, Isere
- Has thanked: 594 times
- Been thanked: 863 times
Re: Hirobo Bearcat SS - Let's start something else...
Small step again... Really need to think how to make this driver figure...
Not sure yet about colours and decoration (yes I procrastinate )... But this is required anyway.
Not sure yet about colours and decoration (yes I procrastinate )... But this is required anyway.
I buy kits to build and ru(i)n them
- silvertriple
- Super Member
- Posts: 1671
- Joined: Sun May 02, 2021 10:31 am
- Location: France, Isere
- Has thanked: 594 times
- Been thanked: 863 times
Re: Hirobo Bearcat SS - Let's start something else...
I did prepared the paint yesterday evening... But I just noticed that my black PS can was almost empty...
Today, once back from work, I decided to gamble on the fact that the can content was enough to do what I need and that was the case as the end... And the can is now really empty...
Few minutes later the paint is over...
I will perhaps add a few stickers, but I really like it this way...
Today, once back from work, I decided to gamble on the fact that the can content was enough to do what I need and that was the case as the end... And the can is now really empty...
Few minutes later the paint is over...
I will perhaps add a few stickers, but I really like it this way...
I buy kits to build and ru(i)n them
-
- Approved Member
- Posts: 3870
- Joined: Sun Apr 24, 2016 2:21 pm
- Location: Guildford UK
- Has thanked: 2287 times
- Been thanked: 1994 times
Re: Hirobo Bearcat SS - Let's start something else...
Some cars really need a driver , just finished it off nicely, I like it as it is as well .
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.
A problem shared is a problem halved but an advantage shared is no advantage at all.
- silvertriple
- Super Member
- Posts: 1671
- Joined: Sun May 02, 2021 10:31 am
- Location: France, Isere
- Has thanked: 594 times
- Been thanked: 863 times
Re: Hirobo Bearcat SS - Let's start something else...
There was something missing on this car...
Added lettering on the tires, but was still unhappy...
So I decided to add leds, and I designed led holders... The side one is printed in TPU, the rear one in ABS (and it relies on the same principles I already used in the past)....
It's much better with leds... But somehow this is missing a wing...
Added lettering on the tires, but was still unhappy...
So I decided to add leds, and I designed led holders... The side one is printed in TPU, the rear one in ABS (and it relies on the same principles I already used in the past)....
It's much better with leds... But somehow this is missing a wing...
I buy kits to build and ru(i)n them
- silvertriple
- Super Member
- Posts: 1671
- Joined: Sun May 02, 2021 10:31 am
- Location: France, Isere
- Has thanked: 594 times
- Been thanked: 863 times
Re: Hirobo Bearcat SS - Let's start something else...
Finishing touch...
Ready to run
Ready to run
I buy kits to build and ru(i)n them
- silvertriple
- Super Member
- Posts: 1671
- Joined: Sun May 02, 2021 10:31 am
- Location: France, Isere
- Has thanked: 594 times
- Been thanked: 863 times
Re: Hirobo Bearcat SS - Let's start something else...
As mentioned somewhere else, I got a second Bearcat SS today...
It came with a box, the original driver, a few missing bits (steering rods - but I need to check inside the box), a broken bumper... Speaking about the bumper, there is an home made one made from a metal plate (3mm thick) which is quite nicely done but very heavy...
Maybe a way to reduce the willingness of the car to go wheelie with the sbsolute power of its 540 silver can
It came with a box, the original driver, a few missing bits (steering rods - but I need to check inside the box), a broken bumper... Speaking about the bumper, there is an home made one made from a metal plate (3mm thick) which is quite nicely done but very heavy...
Maybe a way to reduce the willingness of the car to go wheelie with the sbsolute power of its 540 silver can
I buy kits to build and ru(i)n them
- silvertriple
- Super Member
- Posts: 1671
- Joined: Sun May 02, 2021 10:31 am
- Location: France, Isere
- Has thanked: 594 times
- Been thanked: 863 times
Re: Hirobo Bearcat SS - Let's start something else...
I had the TPU in the printer, ready to roll (and dried as I just printed a sample of 44B rock'n Vega Bumper), so I thought about printing a Bumper to replace the missing one for the Bearcat SS n°2.
The overhang makes it is not perfect...
But for a runner, that will do the work...
The overhang makes it is not perfect...
But for a runner, that will do the work...
I buy kits to build and ru(i)n them
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 19 Replies
- 1430 Views
-
Last post by bearrickster
-
- 4 Replies
- 662 Views
-
Last post by losiXXXman
-
- 51 Replies
- 4484 Views
-
Last post by tomolupus
-
- 12 Replies
- 1354 Views
-
Last post by uniquenamehere
-
- 41 Replies
- 4408 Views
-
Last post by JK Racing
-
- 20 Replies
- 2238 Views
-
Last post by THEYTOOKMYTHUMB
-
- 4 Replies
- 1487 Views
-
Last post by Daddeo
-
- 13 Replies
- 1623 Views
-
Last post by mikedealer
Who is online
Users browsing this forum: No registered users and 2 guests