Incredible_Serious wrote: ↑Sat Nov 13, 2021 6:27 pm
Unbelievable.... Australia Post delivery on a SUNDAY!!!!
Some parts from my good mate Jason....
Parts.jpg
- Four Tamiya TBLE-02S ESCs
- One Tamiya TBLE-04s ESC
- Speed Passion 17.5 Ultra Sportsman V2 motor
- Yeah Racing sensor cable
- PB Mini Mustang set of lower arms, and a couple of diff screws
- M Power 4000mAh LiPo race pack (not pictured, because I forgot )
Plenty of work to do!
Still shocked this delivery came through on a Sunday, at 7:45am......
Alex
PB Ace wishbones there Alex, wheres the rest of the car
XLR8 wrote: ↑Thu Nov 18, 2021 11:00 am
That's an incredible haul Alex.
Where do you find 12th scale wheels and foams these days (for RC12)? Does anyone still make them??
Doug,
They came up in one lot from a seller over here in Aus.... mostly TRC, as can be seen. Some two-hole rears, some three-hole rears, and some pin-drive rears. I think the seller repackages single wheels and pairs that they get from used lots they buy and break up for selling.
All a bit too fiddly for me, as I don't have a 1:12 chassis at the moment! Got a few bodies, got some wheels and tyres, but no actual car.
Alex
Osiris is the key.
"The world looks so much better through beer goggles... except Farmer in his underwear" - Ken
Look out for Todd K. - he's a convicted serial killer!!!
Mike73 wrote: ↑Thu Nov 18, 2021 1:40 pm
PB Ace wishbones there Alex, wheres the rest of the car
I ran out of lower arms for my Mini Mustang project list (three builds on the go), so a good mate sent me these. They're dimensionally the same as the Mini Mustang arms, but with the extra strengthening rib in the middle. Will be fine in a Mini Mustang
Alex
Osiris is the key.
"The world looks so much better through beer goggles... except Farmer in his underwear" - Ken
Look out for Todd K. - he's a convicted serial killer!!!
White Replacement Arms for My RC10T !
I'm still waiting for replacement black arms so this looks a bit hacked but I got some run time in today.
This weekend I got the Avid RC10T4 Top Shaft and a V2 Slipper setup in the mail,
Put in the v2 Slipper modification and oh my my runs so smooth.
Currently waiting on an RC10GT for electric conversion and an RC10T2 off ebay.
Picked this up at a swap meet at my local racetrack yesterday. Wheels look like maybe gold anodized See's? Green endbell Revtech motor and Tekin esc. Couldn't pass up this Pumpkin.
radioactivity wrote: ↑Thu Nov 25, 2021 1:47 pm
I got this "Turkey" in the post.
fao car.JPG
Chuck
You got me, I need to know more?
If a jobs not worth doing then its certainly not worth doing well.
A problem shared is a problem halved but an advantage shared is no advantage at all.
Says "APEX-1" on the bonnet.
Appears to be in pristine condition so maybe it's not as vintage as its 1960's Lotus F1 shape might suggest. Straight axle in the rear (perhaps motor-on-axle like a Tamiya Hornet?) and swing arms up front and front steering.
I have not idea.
Are you gonna tell us about this mystery RC Chuck or keep us guessing?
And I quote...
"Jump into the future of RC racing with the FAO Schwarz RC Classic Racer! The Classic RC Car is ready to run with a sleek, aerodynamic body and shock absorbing wheels. The multi-directional remote control allows for precision turns and drifting!".
I've been digging, doing some research, tapping into the past. On my journey I've Found some very interesting early posts by a lot of currant members here in the archives. Very interesting stuff! I encourage newer members to do the same, as the old...
Last post
Nope. I'm not clicking on any links in this thread because I know one of them is going to be Farmer's pic. :P
None of them were about that picture.
But now one of them refers to it.
But seeing how often it is mentioned in this thread, it sure...
I built this today, its just a start, it was hard to get a picture of the whole track, unless I stood really far away... anyways more to come soon. its gonna be a lot of fun and was not too hard to do for just a few hours work! i made the rails out...
Last post
any suggestions???
thanks
asa
Big jumps and take some pictures of cars in action :D Looks amazing, I'd love a garden!
Thanks to Hoopty for the design, and Mrlexan for the production. They look great. And Thanks again Jay for the body and wing to put them on, can't wait to get 'em dirty. :D
-Anthony
The seller even included a free gift of 4 bearings. Wow, can't wait for my tires to show up too (same as what's in the pic here).
Got a bunch of stuff now, including the RC Channel rear metal kit, SRB alloy chassis and nose. Just need the RC4wd...
Last post
since there is no rc4wd local distributor here in our place, they didnt ship here without approval, wasted a lot of good stuff from them (we need to order in a long process)
Going though my old pitbox I found a untouched b4 sticker set including window masks.
Is there already a scan of these in the group? Otherwise, how would I go about getting a good scan to upload?