Shock bladder/seals

Moderators: scr8p, klavy69

1 post • Page 1 of 1

juicedcoupe: Super Member; Posts: 2989; Joined: Sun Aug 16, 2020 4:05 pm; Location: Pascagoula, MS; Has thanked: 231 times; Been thanked: 1747 times

Shock bladder/seals

Quote

Post by juicedcoupe » Sun Nov 29, 2020 4:30 pm

Has anyone found a readily available replacement for the larger red seals? I know that the rear CVA shocks on Blitzer models used them but I don't know about other models. I figure that with all of the larger bore shocks out there, something is bound to fit.

The green seals used on the front seem to be much more common. Even then, regular Traxxas seals fit perfect.

Always looking for new and interesting ways to waste money.

Post Reply

1 post • Page 1 of 1

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Sign in

Similar Topics

Replies

Views

Last post

Platinum Shock Seals

Last post by radioactivity « Fri Jul 31, 2020 11:23 am
Posted in Kyosho Forum
Replies: 3
by FasterLouder » Thu Jul 30, 2020 5:51 am » in Kyosho Forum

First post

Does anyone know if seal kits for Platinum shocks are still available, or know if a seal from another shock fits them?
My Mid SE shocks are getting weepy. :(

Last post

Sure thing skipper

I believe I still have all/most of the documentation that came with the platinum shocks as jpegs.
I sold a very nice set a couple years ago.
My knowledge of these shocks is not vaste but I did run them for a few seasons in the...

3 Replies

791 Views

Last post by radioactivity
Fri Jul 31, 2020 11:23 am
Shock cap seals

Last post by Caine « Sun Feb 27, 2011 3:44 pm
Posted in Temple's RC10 Tech Forum
Replies: 8
by Caine » Mon Feb 21, 2011 10:17 am » in Temple's RC10 Tech Forum

First post

I know you can buy these in packs of four quite cheaply but is there anywhere you guys know of that they can be purchased in bulk, say 20 or so?

Last post

Thanks for your help guys i now have a good supply of both types of o rings winging they're way to me. Should be enough there for years of shock rebuilds :D

For anyone in the U.K reading this thread they were ordered from:

8 Replies

1129 Views

Last post by Caine
Sun Feb 27, 2011 3:44 pm
HydraDrive Seals

Last post by Mark Westerfield « Thu Dec 15, 2016 12:31 pm
Posted in Losi Forum
Replies: 3
by jkelm24 » Wed Dec 14, 2016 11:31 pm » in Losi Forum

First post

Looking to rebuild a Hydra Drive, but rebuild kits are rare and expensive. Does anyone know the ID / OD measurements of the internal seals?

Thanks!
Jon

Last post

I don't know the size off-hand, but they are generic quad seal o-rings, commonly available.

3 Replies

1059 Views

Last post by Mark Westerfield
Thu Dec 15, 2016 12:31 pm
Felt seals

Last post by a01butal « Mon Sep 24, 2012 4:01 pm
Posted in RC10 Buggy Forum
Replies: 10
by mmdm4 » Wed Sep 19, 2012 3:51 pm » in RC10 Buggy Forum

First post

Where can I get part #6633 the felt seals for the 6 gear diff?

Last post

If you're going to put the bearings into the outdrive holes then maybe you might want to modify the tranny to free it up, this is a cool article which outlines what modifications will reduce friction and let it spin freely.

10 Replies

1840 Views

Last post by a01butal
Mon Sep 24, 2012 4:01 pm
Hydra-Drive seals

Last post by Mark Westerfield « Wed Jun 24, 2020 12:16 pm
Posted in Losi Forum

by Mark Westerfield » Wed Jun 24, 2020 12:16 pm » in Losi Forum

Has anybody already measured and know the size of the the quad-seal (or x-ring) orings inside the Hydra-Drive? I want to get a supply of replacements, maybe try some different compounds.

0 Replies

755 Views

Last post by Mark Westerfield
Wed Jun 24, 2020 12:16 pm
Substitutes or better alternatives to gearbox seals?

Last post by mikedealer « Tue Sep 27, 2011 12:11 am
Posted in Kyosho Forum
Replies: 7
by Coelacanth » Mon Sep 26, 2011 7:23 pm » in Kyosho Forum

First post

The gearbox seals (a thin strip of foam-rubber with adhesive backing on one side) on the Optima series of cars often wear out or dry up and crack. What do you guys suggest as a better or cheaper alternative to the original adhesive sponge strip?

Last post

i would mold some but they would probably cost $10 each to make lol, i think the better option is to have the lexan ones for the torque pinion reproed

7 Replies

1636 Views

Last post by mikedealer
Tue Sep 27, 2011 12:11 am
Dyna Storm Sleeved Damper Seals

Last post by jkelm24 « Wed Dec 09, 2015 12:16 am
Posted in Tamiya Forum
Replies: 1
by jkelm24 » Tue Dec 08, 2015 4:33 pm » in Tamiya Forum

First post

Does anyone know if the DS Sleeved Dampers use the same seals as Tamiya's current CVA and/or TRF dampers?

Thanks!

Last post

Pulled one of mine apart after getting home tonight. I measured the lower sleeved damper seals and they appear to be standard 6mm x 3mm (same as TRF damper and Team Associated gold and Team shocks... along with many others).

Upper cap seals are...

1 Replies

767 Views

Last post by jkelm24
Wed Dec 09, 2015 12:16 am
How would You use "Link End Seals (Balloons)"

Last post by LosiXXkid « Wed Oct 28, 2015 4:19 am
Posted in Losi Forum
Replies: 8
by Jirka » Thu Mar 05, 2015 2:28 am » in Losi Forum

First post

How / where should these be used?

Jirka

Last post

Ah yes, these:
Gils Jrx2 proto with H-arms-F800x600.jpg

Thanks Asso-Man!

Jirka

It's funny, all the Losi instructions that I've ever seen clearly show the female half of the slider connected to the transmission out-drives, that photo quite...

8 Replies

1370 Views

Last post by LosiXXkid
Wed Oct 28, 2015 4:19 am

Return to “Tamiya Forum”

Who is online

Users browsing this forum: No registered users and 14 guests

Shock bladder/seals

Shock bladder/seals

Create an account or sign in to join the discussion

Create an account

Sign in

Who is online

Login Register