All Graphite 6030 Graphite

[fastang]

This is my 6030 6 gear graphite that I purchased a couple years ago new in opened box. As you can see I added a couple hop up parts that I feel fit this car well. The front and rear shock towers are both Composite Craft that were NIP as well as the rare? CC motor plate. I also found the Factory Works battery brace NIP at the bottom of a bin in a LHS. I think it goes good with the CC parts.

Pics aren't the best and I realized after taking them the whole car needs a good cleaning. Maybe I'll pull it apart when im laid up next month. Hope you like it!

[mrlexan]

Very nice, I didn't know that CC made a motor plate. First time I have seen one.

[fastang]

I should have the header card somewhere. I'll see if I can dig it up.

Found it!

[Brat]

Nice and clean!! Always wanted to build one like this but never had a chance as I'll definitely run them.

[fastang]

Can anyone find the flaw on the car? Im sure there are a few build flaws but this one came from AE. Im looking to correct it if anyone has a good one!

[jwscab]

maybe that trans/bulkhead support?

I would put some nice big flat washers behind the heads of the motor screws, to prevent mangling up the carbon fiber; this way the screw head doesn't grind into it.

[LowClassCC]

bass ackwards stealth tranny brace.

front upper spring collars are not in the same position as the rear.

no servo to steering tie rod.

side to side line line on the chassis under the battery.

and your e-clips are not all facing the same direction!



good looking car. didn't somebody make a carbon "shelf bracket" to mount an electric speed controller on the rear tower?

[fastang]

maybe that trans/bulkhead support?

I would put some nice big flat washers behind the heads of the motor screws, to prevent mangling up the carbon fiber; this way the screw head doesn't grind into it.

Nope, not the brace. That was something I added.

The motor screws are really loose to avoid that but I will add washers. Good idea!

[fastang]

bass ackwards stealth tranny brace.

front upper spring collars are not in the same position as the rear.

no servo to steering tie rod.

side to side line line on the chassis under the battery.

and your e-clips are not all facing the same direction!



good looking car. didn't somebody make a carbon "shelf bracket" to mount an electric speed controller on the rear tower?

Almost but not it. Can't give you the prize yet!

[LowClassCC]

whelp unless you are talking about the little spot that looks like it could be a chip of a crack at the hole that intersects that side to side line that runs under the battery you got me stumped.

[minimini]

the Reedy motor seems too modern to match with the car...........

[fastang]

whelp unless you are talking about the little spot that looks like it could be a chip of a crack at the hole that intersects that side to side line that runs under the battery you got me stumped.

Thats actually a fiber sticking up off the surface. There are a few of them on the chassis and I was going to trim them off when I built it but then I thought they are only there once. When new!

minimini you are correct, it is the wrong era motor but still not what I was looking for.

I thought this would be easy for you guys!

[scr8p]

the only thing i see is that you have 3 left side shock collars, and one right. other than that, i don't see any flaws. nice car dude.

[fastang]

the only thing i see is that you have 3 left side shock collars, and one right. other than that, i don't see any flaws. nice car dude.

Ding Ding Ding! We have a winner!

Thats the way it came from AE. 3:1 And I don't have one good enough to replace it!

[scr8p]

i had a shock collar kit that was the same way. i just shaved the little flashing piece off and flipped it around.

your missing the steering linkage too.