jconcepts detonator for rc10

[SteveK]

ok, because you guys have been so patient here's the world's first look at the carbon parts. This has been approved for release to you guys only so PLEASE don't run over to rctech, oople or anywhere else and post these......

Seth, if you're coming over here you better have my Titanium ball studs with you!

Are there sections that are milled out halfway?

[JHarris]

Yes, there are portions which are milled.

I posted the pictures using my computer. The show correctly on the laptop but show upside down on my phone, which is what I used to take the pictures. I'm not sure how they look to you guys but if they're upside down I apologize. I will take some better pictures later and use the camera so they are clearer.

[JK Racing]

Those pictures were clear enough for me! Love the milled out sections, gives them character. JC planning on a battery strap as well? I've heard rumblings about tires too.

[popboy905]

Stoked to see jconcepts supporting the rc10. Are the wheels going to be 1/4 or 3/16? Any chance of a bell crank, wing mounts maybe?

[ra272]

I'd love some "SC style" wheels, 1.7/2.2 with the look of the 1.7 and the performance of the 2.2.

[JHarris]

Here's a few more pics of the carbon parts. Could the stealth tranny brace and world's front tower be a sign of things to come??????

[JHarris]

And the parts installed....

[JHarris]

Stoked to see jconcepts supporting the rc10. Are the wheels going to be 1/4 or 3/16? Any chance of a bell crank, wing mounts maybe?

Since there are current options for a 3/16 wheel, I don't see the need for JConcepts to produce that size, especially considering the size of the market not being the same as modern cars. Also, I know Jason Ruona is attempting to keep the RC10 classic as close to stock as possible. That includes the drive line and wheel sizes. You can reasonably assume a few things from that statement....

While I can't disclose exact product plans I can tell you that JConcepts produces aftermarket products for a wide variety of vehicles. If you look at the products they have made for those vehicles you could probably make reasonable assumptions about planned products for the RC10.

I can't yet discuss the style of the wheels that may or may not be in the works, but I think most everyone will be happy.

As for the body..... This morning Larry at Kustomrcgraphics texted me pictures of mine with paint. I hope to be able to share those with you guys very soon!

[seth556]

Is this the body?!

[rctenracer]

Is this the body?!

Thats a protech body.

[popboy905]

Thanks jharris, so 1/4 rulux wheels could be a maybe ? Or hex conversion to use the 1/16 revo wheels? Titanium turn buckle set... I'll just have to wait and see

[teman]

Thanks for all the info Jeff, I can't wait too see the new body

[JK Racing]

Mmmm, you tease with just enough to keep us all salivating and hungry....nice paint on that Protech I up there, I like it.

I'd like to see a Monroe style battery strap, some alloy steering and rear hex kit for the Rulux MERV wheels as well (a correct offset Rulux front to match would be great!)

Where do we submit the wish lists? Is there a [email protected] address or something we can send to

[MH7]

I'd like to see some 2.2 dished wheels for both front and rear. So modern tyres can be run without needing to convert anything (basically re make b2 wheels) And a bodyshell that's as close to the original RCPS mirage of the worlds car as possible. As that was by far the best look for the RC10.

[JHarris]

The body was just released. I can't post pics from my phone but head over to the JConceptd Facebook page or website (blog) and check it out. I will post pics of mine later today.