It’s been about long enough since my last chassis. Since I ordered my sons rc10t re-releases I thought I should make some chassis for them.
I seem to be getting better year over year. Hopefully I can make something meaningful to them. As well if the tooling comes out well I’ll have my oldest make a chassis.
I’ll re-read my previous threads but I already know I need to build new tooling to make a quality chassis.
I am fully sacrificing a nose plate as well as well as chassis that was in good condition to begin with.
This is of course to put off the current build even further. I should be building an edinger I collected parts for years and can finally start on. So here is what I did instead
Sanded to get things flatter
Sits flat on the tile
Using bondo and release
Previous attempt notes here
https://www.rc10talk.com/viewtopic.php?p=540329#p540329
Relevant Notes here
https://www.rc10talk.com/viewtopic.php?f=113&t=48258
The T3 chassis at the end of this thread
https://www.rc10talk.com/viewtopic.php?t=47048&start=60
turned out well and fixed a few issues I was having with the April build. It was a good runner without being overbuild. Did well considering the steel pole I ran it into a full throttle.
though this was a direct pull and not cast from tooling.
Looks like the resin ratio should be less than 1:1
I never solved the issues with wrinkles in cast parts, though on the 2 part made from direct pulls the inside was smooth. I think the wrinkles are partly caused by excess resin.
The wrinkles make the part NG since the finishing is excessive.
I don't have any gelcoat. Given the summer temps. I am not sure that I can use it without waiting for fall.
8 layers of plain weave 3k 5.7 oz fabric should be about 2.1mm thick
Switching to west system from US composite resin. I am also switching to a ultra slow cure resin. It is supposed to be more rigid on full cure than the faster set ones.
Making a carbon fiber rc10t chassis the Competent way
-
- Approved Member
- Posts: 1589
- Joined: Thu Mar 23, 2017 5:31 pm
- Has thanked: 1042 times
- Been thanked: 481 times
-
- Approved Member
- Posts: 1589
- Joined: Thu Mar 23, 2017 5:31 pm
- Has thanked: 1042 times
- Been thanked: 481 times
Re: Making a carbon fiber rc10t chassis the Competent way
Nothing shows off what you missed in finish better than clear coat.
I think I made good progress. The chassis is flat, the area between the nose plate and the chassis are filled.
I also evened out the sides so the metal lip is smooth.
The clear coat should provide a mirror smooth surface for the tooling.
I think I made good progress. The chassis is flat, the area between the nose plate and the chassis are filled.
I also evened out the sides so the metal lip is smooth.
The clear coat should provide a mirror smooth surface for the tooling.
-
- Approved Member
- Posts: 1589
- Joined: Thu Mar 23, 2017 5:31 pm
- Has thanked: 1042 times
- Been thanked: 481 times
Re: Making a carbon fiber rc10t chassis the Competent way
Mounting up the tool to an acrylic blank
And waxing
2 coats of clear
6 paste wax of 5
3 coats of man’s 2300
Clay was used to fill the nose and tail as well as to form a bead around the chassis
The width of the nose and tail were widened to that the tooling would not curl or round in those areas
The height of the wall was increased with clay to reduce rounding near the top of the chassis.
The rear bulkhead stay has been a challenge to mold and will continue to be. May just build a wide bulkhead and use shim/washers to build the gap.
And waxing
2 coats of clear
6 paste wax of 5
3 coats of man’s 2300
Clay was used to fill the nose and tail as well as to form a bead around the chassis
The width of the nose and tail were widened to that the tooling would not curl or round in those areas
The height of the wall was increased with clay to reduce rounding near the top of the chassis.
The rear bulkhead stay has been a challenge to mold and will continue to be. May just build a wide bulkhead and use shim/washers to build the gap.
-
- Approved Member
- Posts: 1589
- Joined: Thu Mar 23, 2017 5:31 pm
- Has thanked: 1042 times
- Been thanked: 481 times
Re: Making a carbon fiber rc10t chassis the Competent way
I am out of gel coat and will try using the remaining epoxy I have from my previous batch as a surface coat that will be backed by satin weave fiber glass
Coats will be .4 oz resin .1 oz hardener
Will be applied by brush
This was not successful. I was out of vacuum bagging materiel. Then I decided to use some clay to hold the sides down, completely forgetting that other times I had a release film between the clay and the resin.
I'll have to see if anything comes out of this.
Coats will be .4 oz resin .1 oz hardener
Will be applied by brush
This was not successful. I was out of vacuum bagging materiel. Then I decided to use some clay to hold the sides down, completely forgetting that other times I had a release film between the clay and the resin.
I'll have to see if anything comes out of this.
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 70 Replies
- 6202 Views
-
Last post by JosephS
-
- 18 Replies
- 1021 Views
-
Last post by JosephS
-
- 30 Replies
- 1834 Views
-
Last post by JosephS
-
- 5 Replies
- 998 Views
-
Last post by necka
-
- 10 Replies
- 2043 Views
-
Last post by durb69
-
- 10 Replies
- 1805 Views
-
Last post by Speed Chaser
-
- 17 Replies
- 1259 Views
-
Last post by JosephS
-
- 18 Replies
- 3092 Views
-
Last post by JosephS
Who is online
Users browsing this forum: No registered users and 17 guests