rc10ds axles 8868 vs ASC9670 b4 stub Axle /general ds axle options

[JosephS]

Hello all,
I am working on assembling a DS conversion and have some questions on what options are available for axles, hubs and drive shafts.
I am looking at the stock parts, but would welcome suggestions on subbing in easier to source parts that could work with a conversion.

Stub Axles
Is the Ds stub axle 8868 interchangeable with the b4 stub axles 9670?

Team-Associated-RC10DS-Dual-Sport-Rear-Stub-Axle.jpg (1.73 KiB) Viewed 1195 times

Team-Associated-RC10DS-Dual-Sport-Rear-Stub-Axle.jpg (1.73 KiB) Viewed 1195 times

Hubs
It looks like the rear axle hub part is the same as the worlds car part 7368 and the b4 axles work for that conversion.

7358_md.jpg (3.03 KiB) Viewed 1195 times

7358_md.jpg (3.03 KiB) Viewed 1195 times

So it seems that should work. Can the older style hub work with the correct flanged bearings?

6366_md.jpg (2.66 KiB) Viewed 1195 times

6366_md.jpg (2.66 KiB) Viewed 1195 times

Can the b4/t4 hubs (9584) be used to adapt different axles?

9584_md.jpg (9.02 KiB) Viewed 1195 times

9584_md.jpg (9.02 KiB) Viewed 1195 times

[/url]

Drive shafts
What are the lengths for the dog bones 8867?

8867.jpg (11.42 KiB) Viewed 1195 times

8867.jpg (11.42 KiB) Viewed 1195 times

Is there a reasonable alternative for drive shafts and axles?

[jwscab]

The b4 axles will work they will be slightly wider and need to use blue spacer. About 2mm.

All the hubs shown except the b4 hubs will work. B4 hubs pushes out approx 3/8".

The bones are short. Maybe like 30-35mm?

[GoMachV]

JC racing is working on Dual Sport universals as well as buggy and truck universals. Old school style, not the modern CV

[JosephS]

The b4 axles will work they will be slightly wider and need to use blue spacer. About 2mm.

All the hubs shown except the b4 hubs will work. B4 hubs pushes out approx 3/8".

The bones are short. Maybe like 30-35mm?

Thanks for the the info on the axles. I have a set of the b4 ones so that saves a hunt.

Do you have any to measure?


So with regular hubs it would be somewhere in the 1 1/16 - 1 3/8 th of an inch
b4 hubs would be 1 7/16 - 1 3/4 (39-44mm)

is the ball size 8 mm?
I found a few candidates depending on the length

would yokomo cvd' sand customworks axles work?

[JosephS]

JC racing is working on Dual Sport universals as well as buggy and truck universals. Old school style, not the modern CV

Do they any clue when they may be ready? I can wait on this build for a while.

[GoMachV]

I believe the rc10 and 10t universals are coming first, they were asking me to double check measurements just last week on the DS uni’s. Hard to say for sure but maybe shoot them an email (I talk to them mainly on Facebook messenger).

https://www.jcracingproducts.co.uk/vintage-car-spares

[JosephS]

I believe the rc10 and 10t universals are coming first, they were asking me to double check measurements just last week on the DS uni’s. Hard to say for sure but maybe shoot them an email (I talk to them mainly on Facebook messenger).

https://www.jcracingproducts.co.uk/vintage-car-spares

They made it sounds like they will know the release of the DS shafts mid month. The price seems reasonable from what they are targeting around $50 usd. I'll have to see what actually shakes out, but I'll wait for to see what happens.