Intriguing ad in RC Car Action - RC10 re-release?

[orangemazda]

My local hobby shop had 2 of them today! I just went down and bought my second one!

Now I've got one to show, one to go.

[Diamond Dave]

Wow those people paying 300+ are gonna be mad

That's what I'm saying. Patience is a virtue especially in this hobby.

I agree. I picked up a few kits from a smaller hobby shop in town, then I waited til the big dogs (Rod ) got my order in. Snapped up two more. Heck of deal with the pre order price.

Not sure what each one is going to be for, but I am sure I will figure it out.

[flipwils11]

Not sure what's going on with the delays on parts, but Tower's status keeps updating..... late Oct, early Nov, now it's mid-Nov. I'm waiting for an order of the steering bellcranks, some rear arm mounts, and bulkheads. WTF, does anyone have any insight into the delay on the Associated re-re parts that were promised?

The black nose plate is also perpetually delayed it seems.

[flipwils11]

No responses, I'll try again. I know a few of you bought parts like the rear bulkheads when they were first released. Anyone else like me waiting on orders for spare parts that seem to be perpetually delayed?

[SnoopMaxx]

Yeah I'm waiting on a-arms and suspension mounts
for my Roger Curtis build

[menace]

Yeah I'm waiting on a-arms and suspension mounts
for my Roger Curtis build

Amain has them in stock.

[ca-rj]

Steering belcrank 6252 in stock on RC10.com. Just ordered 2.

[janaya]

Anyone replace their felt seals for bearing on the out drives of the 6 gear tranny? What size did you go with?

[SnoopMaxx]

Yeah I'm waiting on a-arms and suspension mounts
for my Roger Curtis build

Amain has them in stock.

already ordered them from Tower
but it can take from 3 to 4 weeks as they have to ship to Denmark


janaya
I used 3/8" x 5/8"
the ones that support the diff in the 3 gear tranny
and I made two spacers 3,6mm wide

[THE H.P FREAK]

HI!... I did,



I also doubled up the bearings in the axle drive gears.

[SnoopMaxx]

The standard inner bearing is not needed
The new outer bearing will support the gear just fine

[janaya]

What size are those bearings? I'm looking at upgrading and run the 6 gear before decide to swap out to a stealth.

HI!... I did,



I also doubled up the bearings in the axle drive gears.

[THE H.P FREAK]

The standard inner bearing is not needed
The new outer bearing will support the gear just fine

HI!... I find that they are. The oilite bushing is twice as wide as the single bearing that replaces it. Half the support. Doubling up on the bearing returns the full support. I've never had a problem once I started doubling them up. A fast BL systems will kill the single bearing quickly. Been there, done that. For the extra $2 well worth it IMO.

[janaya]

Thanks didn't see it till just now.

janaya
I used 3/8" x 5/8"
the ones that support the diff in the 3 gear tranny
and I made two spacers 3,6mm wide[/quote]

[SnoopMaxx]

The standard inner bearing is not needed
The new outer bearing will support the gear just fine

HI!... I find that they are. The oilite bushing is twice as wide as the single bearing that replaces it. Half the support. Doubling up on the bearing returns the full support. I've never had a problem once I started doubling them up. A fast BL systems will kill the single bearing quickly. Been there, done that. For the extra $2 well worth it IMO.

Noted
I'm only using a stock brushed motor in mine, for now