Hi,I'm new to this forum. I was trying to find info about a article on a parking lot racer Rc10 buggy. I would like to know if someone has the article and could email me it. I found some info on here,but I lost it. I'm not good on a computor at all. I remember this article and had the maganize, but misplaced it. Just got back into the hobby. Thanks Ken
Is that the one where they used turnbuckles to replace the front shocks or are you looking for an article on a conversion kit like the Agitator-Jammer?
Ken Rc10 wrote:Hi,I'm new to this forum. I was trying to find info about a article on a parking lot racer Rc10 buggy. I would like to know if someone has the article and could email me it. I found some info on here,but I lost it. I'm not good on a computor at all. I remember this article and had the maganize, but misplaced it. Just got back into the hobby. Thanks Ken
Thanks for all the help. After a lot of reserach if found the article on the conversion.if anybody is looking for it its in RCCA, Feb 1995 issue. Also someone was looking for a mid engine conversion. I found its in the RCCA issue Oct 1990. Hope this info helps. Thanks Ken
Hope I’m ok to post this here. Hard to find the below parts wondering if anyone can help? Another question about the CVA as well: I have a ASC 9911 - B44.2 center/rear CVA bone could I just get a longer dog bone (I.e. just the dog bone from a B44)...
Last post
You might try these if you still need ASC 9608.
GoMachV on this forum is Factory Works.
I was wondering what is the standard (US Measurement) Thickness of the RC10L Chassis, and does anyone know the type of Fiberglass used? I am trying to make a replica chassis with a few minor modifications.
Thanks-
Last post
Thanks, I will look out for some G10 /FR4 in that strength
As for the T-bar, they vary in thickness depending on what setup you want, and I was looking for the chassis itself. The composite craft T-bar could be a thin, or thick version.
I'm rebuilding another 10T. The rear hubs are marked only with a 0 (zero) no L for left. Does the 0 designate zero degrees? Are they aftermarket (RPM)?
Also, the rear suspension mounts are marked with a 3 on each. 3 degrees?
I've only ever used...
Last post
hey dude bodys ready and i have your wanted laundry list nose hubs mounts you would be best changing the nose seems pointless to be so precise on the rear to have rebent nose :wink: will be home tonight.
Thanks for this great forum, I know this has been answered before. I have tried the search and came up empty. In one of the early RC10 Manuals it states to OIL the Bushings in the tranny and rear end. What is a good modern oil to use during a...
Last post
gomachv, Thanks so much for your tip on the R/C Shop out in Oregon. I called them and got the last set of #6614 Idlers that they had. They are also looking for some other parts for me at this time. Thanks again!
I know this is for rc10s only but can anyone tell me where to find info on the RC8b I was hoping to find a site with a form like this one to get some info thanks.
Last post
yup, rctech has a huge thread for both the rc8be and the rc8e.2.
any specific info you need? i own and race a rc8be. the car doesn't really need much.
HI!... I just acquired both of these items in a RC10 DS lot buy. 1st is a clear uncut body. It is made by PROTO-FORM. Part # is 1412. It is called a GTS-1 Aurora. It also has DS formed into the top of the windshield. I have no decals with it and...
Last post
I wasn't able to find any descent pictures of it.
Any decent picture will do, it doesn't need to be going down.
looks ma no paint. it appears you can strip paint off your composite craft chassis with no ill affects... lucky me! :D
still gonna be the last time I paint graphite though :roll:
Hi, I’m looking for some info on my motor. It has the same coloring/sticker (bright pink) as the Trinity nuclear assault, but it has a plastic end bell - all the info I can find via Google shows an aluminum end bell for the nuclear assault. I saw a...
Last post
Hi, I’m looking for some info on my motor. It has the same coloring/sticker (bright pink) as the Trinity nuclear assault, but it has a plastic end bell - all the info I can find via Google shows an aluminum end bell for the nuclear assault. I saw a...
