Just got this bad boy from eBay it's super clean and has rpm parts. I need help identifying the bellcrank and the turnbuckles. Also is this a team truck? The manual says its from 91 and the truck was assembled with parts from the team buggy. Tell me what you think and will a tekin rs and a d3 17.5 be ok for the tranny
Looks like a team truck as well, but then again the shock towers ( I think ) should be white, at least they are on mine. Nice clean truck you have there though!
Wow thanks for the fast replies this will be a work in progress should be done around may. Can I get servo mounts or am I just going to tape the servo? I would rather bolt it down than tape it.
I would suggest T4 CVD's. You would get the benefits of CVD's, and you would be able to share wheels with your T4. You would also need the aluminum spacers from the T4, and 3/16 wheel bearings.
justinspeed79 wrote:I would suggest T4 CVD's. You would get the benefits of CVD's, and you would be able to share wheels with your T4. You would also need the aluminum spacers from the T4, and 3/16 wheel bearings.
Nice tomorrow is race night at the lhs ill pick up bearings and cvd's. will I need to mod the rear hubs?
justinspeed79 wrote:I would suggest T4 CVD's. You would get the benefits of CVD's, and you would be able to share wheels with your T4. You would also need the aluminum spacers from the T4, and 3/16 wheel bearings.
Nice tomorrow is race night at the lhs ill pick up bearings and cvd's. will I need to mod the rear hubs?
No mods except maybe moving some shims around. Don't forget the T4/B4 aluminum wheel spacers. They're the ones that go between the outer bearing and the axle pin.
I'm 29 years old, which makes the team moo Rc10t roughly the same age as myself. When I was probably 7-8 years old I saw a flash back post in a rc magazine on cliff letts Rc10t with the iconic cow front end paint scheme. Since that...
Last post
Beautiful truck, glad you are driving it and enjoying it. I too, have my version of Cliff Letts truck and have a thread on it here. I did buy carbon towers and Factoryworks rims inspired by the Jconcepts truck article on their website from 2017. And...
My father bought my brother and I these about 20 years ago when they first came out, we spent alot of time building our trucks and learned alot. I used it casually on and off for 7 years or so probably. I have since decided to pull it out of the...
Last post
The nice thing about the 10T is that the 10T2 and the GT shared the same geometry arms and the GT was in production until just a few years ago. The parts were a little different structurally but everything else is the same. If you broke almost...
I picked this up just recently. Did not expect the guy to accept my price, but here it is. It was an impulse buy for certain.
CE version with an 'A' stamped chassis.
With: Novak Mercury receiver, HPI Racing ESC, Futaba servo, original AE...
Last post
Built to run in my opinion. these things are selling for alot on ebay right now. Cant seem to understand why that is. lol! Especially when I picked one up a couple years ago for $75 shipped.
Here is some pics of my shelf queen. I have owned her from new. To give you a little history, My mom and dad bought the car when I was a kid and built it, we ran it very little. It was never raced and has spent most of its life in boxes. It is and...
Last post
You say the 80's had one hit music??? Have you listened to music lately?? :lol:
I got a perfect early JRX-2 from a member here and after receiving it I cleaned the dust off, the shock shafts ( love that old Losi water based shock fluid ) and it seemed odd that this car was built in 89' then never touched. The one key might be...
Last post
I have a couple rc10t2 without tranny gears or axles. I suspect that someone had a GT, and took a couple parts from the t2 to fix their GT and then the t2 sat untouched. One of these t2 i bought on ebay, the owner said he bought it at a vintage...