Hello everyone I am new to the RC world and have just purchased a an old RC10T from craigslist.
My plan is to drive it around the house and local track. I may want to enter into some local races depend how much I like it.
I am guessing that I will need to restore it but I do not know with what parts. From what I have read I should upgrade the sealth to one from RPM, replace all the bearings and upgrade to brushless. Are there specific parts/brands that I should look for getting this parts? One thing I notice that most RC10Ts that I see have white parts were as mine has blue.
I tried the search but I really do not even now where to start.
The guys here have been awesome answering all my newbie questions and you should gain a lot of beginner knowledge reading through that thread then you can ask more specific questions to your rebuild
You don't necessarily have to replace the bearings. Only if they are worn out and wobble. I'd definitely keep the Stealth tranny and spend money somewhere else on the truck. As for brushless it is much more convenient, but if you're just getting into it I'd wait since it looks like that Novak esc looks to be in good shape.
That truck looks to be pretty well taken care of and outfitted nicely. Have you run it with that motor in it yet? If so, how'd it do?
"The world looks so much better through beer goggles: Enjoy today, you never know what tomorrow may bring." Ken
I agree with above posts. I would keep the stealth and the brushed steup for now. Instead, put your money into a LiPO battery and a low voltage cutoff module. A new body and some new tires. Try that until the motor burns out and then upgrade to BL then. Of course that is just my opinion. It is ALL up to you!
If you are interested in racing, there are a few things to know to make your ventures fruitful. First, make sure the truck is in good mechanical condition to minimize DNF's. Second make sure you have the proper tires, and inserts. This is the single biggest part of properly setting your car up. Third, practice and ask questions of your fellow racers regarding setup, track etiquette, and how the races are run at your local track. Fourth, be persistent. I have helped countless #'s of newbies over the last 20+years, and you can expect at least 4-5 racedays before you really get the bugs worked out, are comfortable on the track, and can have a full "uneventfull" raceday under your belt. Lastly try your best to have fun with it. -Jeff
I was in sort of a similar boat because I was re-entering the world of RC after more than 20 years out of the hobby. Everything had changed so I really didn't know anything anymore.
This place is an absolutely amazing resource and all you need to do is read, read, read. It's likely that the majority of your questions have already been answered here in one way or another.
What I would do is this:
1. Start out by looking at what other people have in their cars. Keep in mind that the RC10T and RC10 buggy share some of their basic running gear, really only the nose and arms / turnbuckles etc. are different.
2. Run your truck with a stock motor, battery and basic radio. No need to spend a lot until you get comfortable with what it can do and you figure out if you like the hobby or not.
3. If you get addicted (like you probably will), start with the easy upgrades: battery, ESC, motor. These are bolt in parts which will get you a lot more bang for not a lot of dollars (in general) and you can go from there. I would recommend Gens Ace Lipo batteries as they are cheap, but great batteries (see Hobbypartz.com). As for ESC and motor, its a matter of personal preference but in general these days, a brushless motor is really great for speed and because they are maintenance free compared to the old brushed motors. I personally have a Castle Mamba Max Pro and their 4600 kv motor. Its a potent quality setup, but didn't cost an arm and leg either.
Once you've done these things you'll get a better flavor for what the hobby is all about and you can start learning about your amazing new truck!
Mr. voodoolite,
You are new to the hobby and your first rc purchase is a rc10t ..AND you found this board and posted on it?!...I think you are already addicted
Welcome and nice truck!
Been working on a B2 I picked up just have a few questions.
Did all the B2's have the skinny rear chassis plate or did late versions come with the extended 9241 plates? I have a Late B2 but it has the 9241 rear chassis plate with the updated 9267...
Last post
maybe your car had the b3 conversion installed. or, worn out parts were just replaced.
i don't know off hand what all came in those conversion kits.
Here's a pic of a sealed B2-to-B3 conversion currently on ebay if it helps:
I just did a complete tear-down of my MX-4 today, and wanted to know if you guys could help me I.D. it more specifically? I bought it from Reggie a while ago, and I think he bought it from someone on RC Tech because that's where I found these pics...
Last post
The motor mount looks like a custom job (rather crude compared to the other parts). For the top shock mount, I think it exists in blue as an option.
My Jrx2 build is coming on, but always seem to be searching for parts! The original short chassis is proving to be a big challenge but I will have to be patient. In the meantime please can you help me with a few question...
- are there any...
Last post
Thanks guys, really helpful as normal. Will have to spend some time taking in all the collects on the different wheel options.
Hi,
what can i use for replace the DS Universals ?
Thanks
Last post
DS is kinda unique there. You could use standard axles and DS bones. You may also be able to source some CVD type axles, but it would have to be a mix and match gamble kind of thing. maybe a TC3 or NTC3 something might be a usable source. I think...
So I want to change the battery placement on my gold pan from being across the body to run with the body. Now i can make that happen with out issue but the futuba esc i have that mounts the same as the steering servo has no place to go that can...
Last post
i see it now, its the hole along the bottom edge that isnt at one of the corners on the plate.
Hey guys.I got myself a T4 from a good buddy and know very little about it.It`s a roller in new condition and would like to know the diff between a T4 and a B4.Is there any reason I couldnt put F&R shock mounts off a B4 on this thing and run a B4...
Last post
Thanks alot for the input guys.I think I`ll leave it as is.I have never owned one and dont know diddley about them. We have a bunch of xxt`s we beat on regularly so I am considering making a shelfer out of this one.Its got cv joint type drive...
I got a set of rims like what Jay Halsey used on his 1985 IFMAR winning buggy. What bearings or bearing inserts did he use? Does anyone have a link to where I can get what I will need?
Also, does anyone have a lead on the right tires for...
I have been rebuilding my old RC10 A stamp that I had when I was a kid in the 80s. It's almost ready to run, but I have a few questions, if you fine folks could help me out. I've been trying to find the answers myself, but have not had much...
Last post
Home Depot sells internal retaining clips but I don't remember if they've got the right size for the shocks. I know they've got the correct size for the 6-gear outdrive gears.