Search found more than 1175 matches
- Tue Dec 27, 2016 7:59 pm
- Jump to forum
- Jump to topic
Re: Cadillac RC10 set screw size - Front lower shock mount
If your talking about the screw that retains the pin holding the shock to the arm on a short arm car, it's an .050
- Wed May 10, 2017 8:32 pm
- Jump to forum
- Jump to topic
TRX-B (poor mans TRX3) and SRT-R (you guessed it!)
Not a difficult conversion, but since the TRX3 front bulkhead is so hard to find I used a Rustler/Bandit clip in whole. The rear is stock Bandit with a Nitro Stampede bulkhead (will need spacers) or a TRX-3 will bolt right up as well. I'll made a short brace for the trans to the bulkhead. The batter...
- Wed Aug 09, 2017 12:10 pm
- Jump to forum
- Jump to topic
Re: 3D Printed Stainless Steel Outdrives
The extended versions would also solve the "Lethal Weapon in a Kyosho/Tamiya application" problem, as their outdrives were a bit longer. I'm really hoping these work out!
- Wed Aug 09, 2017 12:15 pm
- Jump to forum
- Jump to topic
Re: 3D Printed Stainless Steel Outdrives
More than I expected- I just measured it and would need 6mm per side
- Wed Aug 09, 2017 2:21 pm
- Jump to forum
- Jump to topic
Re: 3D Printed Stainless Steel Outdrives
Not sure, but the user that printed his stainless dogbones said they were holding up great, so I have hope!
- Wed Aug 16, 2017 11:48 pm
- Jump to forum
- Jump to topic
Re: Need a Little help with RC10 Body Identification
Those are the earlier ones, much better quality and thicker lexan than the late bodies. Probably more of those made over the years than any other body, but also more of them destroyed lol. Good body, deserves to be on a special build. If your gonna build a runner use a cheap new body and keep this a...
- Sat Aug 26, 2017 8:40 pm
- Jump to forum
- Jump to topic
Twice as Lethal 6x4 Truck Conversion
I can't let Daryl have all the fun From the outside it's a throwback to his truck but this one runs dual Lethal Weapons with off the shelf components instead of the hand built chain drive single motor setup. I also went with buggy components and truck offset wheels. I think the offset wheels fit the...
- Wed Sep 27, 2017 12:23 am
- Jump to forum
- Jump to topic
Re: Steel and Aluminum RC10 Outdrives-- Coming Soon!
Brian hasnt updated so I will...the current selection is for the Aluminum drives. I believe he has a batch ready to sell The steel outdrives became an issue, one side was too long. I am working with the manufacturer to see if they can make the sides equal length for us. Currently the entire stock is...
- Thu Nov 30, 2017 9:40 am
- Jump to forum
- Jump to topic
Re: Quadra-symmetric RC10
Very nice Niki! This will be a popular piece
- Sun Dec 03, 2017 7:43 pm
- Jump to forum
- Jump to topic
Tinkering with a 10L
This is my latest project. I’m pretty excited to finally put this crazy idea that’s been stuck in my head for a while now Not only is the chassis lipo compatible (standard or shorty) but it also retains the T plate styling that is simple and effective, as well as the stock shock and dampener assembl...
- Tue Dec 12, 2017 12:59 am
- Jump to forum
- Jump to topic
Re: Quadra-symmetric RC10
Here’s the tower set (also shown is one of my trans braces)
- Fri Dec 29, 2017 1:43 pm
- Jump to forum
- Jump to topic
Re: Ishipla Monster
Need more just let me know!
- Thu Jan 25, 2018 11:36 am
- Jump to forum
- Jump to topic
Re: Which exact black Rit-Dye to tint old AE nylon? (And how?)
I don’t know how to link you to the best place to get it where your at, but the part number is 02227 and it’s called Rit Dyemore Graphite. They are all over eBay but no idea with shipping which is the best price. It’s also on Amazon but I’m not sure if you have Amazon You will dilute it with water, ...
- Mon Jun 18, 2018 9:19 pm
- Jump to forum
- Jump to topic
Re: The Official "What is it?" Thread
My bad, only came with wheel no tire