Page 1 of 1
Can someone measure a wing tube for me please????
Posted: Mon Oct 10, 2011 3:54 am
by Caine
Can someone accurately measure the length of an RC10 wing tube for me please, both sets i have are wedged into the bulkheads and i fear damaging them if thet are pulled out with to much force!
Thankyou
![Very Happy :D](./images/smilies/icon_biggrin.gif)
Re: Can someone measure a wing tube for me please????
Posted: Mon Oct 10, 2011 7:33 am
by dragnse7en
The wing tube's diameter is 3/16" or close to 5mm.
The wing tube's length is 2-3/64" or around 52mm.
I wouldn't worry about damaging them when you pull them out. Use a cloth in between the pliers and tube if you're afraid of leaving tool marks on them. I didn't need to do this, however, I am going to clean, polish and seal mine before I re-install them.
Re: Can someone measure a wing tube for me please????
Posted: Mon Oct 10, 2011 7:38 am
by scr8p
there are 2 different length wing tubes, depending on which bulkhead you have.
Re: Can someone measure a wing tube for me please????
Posted: Mon Oct 10, 2011 7:39 am
by dragnse7en
The tubes I mentioned are for the cadillac era car/ A stamp car.
Re: Can someone measure a wing tube for me please????
Posted: Mon Oct 10, 2011 7:46 am
by Caine
I need the later ones please, team car etc
Thanks for taking the time to measure yours for me, mine are really really wedged in to the bulkheads, i have tried in vain to remove them!
This set is for my old is new car which has a protech body and rpm bulkhead if that makes any difference for length etc?
Re: Can someone measure a wing tube for me please????
Posted: Mon Oct 10, 2011 9:10 am
by jwscab
if you can take the tower off the bulkhead, and you have a drill, you can chuck the tubing in the drill chuck and wiggle/twist the chuck and bulkhead, the tubes should come out without marring up the tubing.
you are basically using the drill chuck as a 'handle' and the three jaws prevents you from marring up the tubing or collapsing it.
Re: Can someone measure a wing tube for me please????
Posted: Mon Oct 10, 2011 6:15 pm
by rctenracer
wing tubes are tight at times and are just pressed into bulkhead . Try putting the bulkhead and tubes in boilng water that should free them up. But if you mess them up try these.
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXS020&P=7
Re: Can someone measure a wing tube for me please????
Posted: Mon Oct 10, 2011 6:27 pm
by dragnse7en
I wish someone would reply to my battery strap thread. Yeah - off-topic. But I'm now sorta jealous that this thread is getting more attention than the simple question that I asked for.
![Sad :(](./images/smilies/icon_sad.gif)
Re: Can someone measure a wing tube for me please????
Posted: Mon Oct 10, 2011 6:51 pm
by rctenracer
dragnse7en wrote:I wish someone would reply to my battery strap thread. Yeah - off-topic. But I'm now sorta jealous that this thread is getting more attention than the simple question that I asked for.
![Sad :(](./images/smilies/icon_sad.gif)
Try posting in the wanted thread. I just looked in the parts box I have and no strap or I would send it to ya for free.
Re: Can someone measure a wing tube for me please????
Posted: Mon Oct 10, 2011 6:54 pm
by dragnse7en
rctenracer wrote:dragnse7en wrote:I wish someone would reply to my battery strap thread. Yeah - off-topic. But I'm now sorta jealous that this thread is getting more attention than the simple question that I asked for.
![Sad :(](./images/smilies/icon_sad.gif)
Try posting in the wanted thread. I just looked in the parts box I have and no strap or I would send it to ya for free.
Thank you for your feedback.
Re: Can someone measure a wing tube for me please????
Posted: Mon Oct 10, 2011 8:32 pm
by jwscab
the long tubes on the first run bulkhead is about 2.4" long. Close enough for the application.
the link above from tower on the 3/16" tubing is a direct fit.
Re: Can someone measure a wing tube for me please????
Posted: Tue Oct 11, 2011 5:36 pm
by Caine
Thanks for the tips guys
I doubt very much i would of thought of those ways to remove them!