RC10Talk - The Net's Largest Vintage R/C Community

Being a big fan of the Losi XX, I was never really into the RC10 buggy, until you guys made a fan out of me with some sweet RC10 (Old is New) buggy builds, I had to have my own copy of those cars. After some research, and bugging some of you guys on RC10Talk, here's what I'm starting out with:

RC10 Graphite Team Car
RC10T Chassis and Nose plate
RC10T Front bulkhead
RC10T2 Front Shock Tower
Aluminum Steering Bell Crank
Associated Viper Body
Associated Factory Team Shocks
RC10T rear Shock Tower (I want the graphite tower)
Klein Arms (ordered)
RPM 10T rear hubs

and a whole lot of stuff I might be forgetting

Still to come:
Powder coated chassis
JC B4 Wing
B44 Axles

and other stuff I can't remember right now....

Just dropped off the chassis to be stripped and powder coated

Looks like this is going to be a great build!


ED

I just hope I can take pictures as I go, instead of just building it and taking a picture afterwards...

I received the Klein arms the front end is basically assembled, I'll post some pictures when I get home.

As I was assembling the front end, the inner hinge pins from the buggy won't work with the klein arms, I need the 10t front inner hinge pins.

Do they sell the front inner hinge pins separate??

Do I need the 10t rear hinge pins??

Front hinge pins....

http://67.199.85.166/main/productdetails.php?text=7209
or
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LX2916&P=7

As for the rears, I believe AE used the same rear inner pins on the buggies as the trucks for the later rear arms. If yours were the early arms they will be just a tad longer than truck pins. I'm unsure as to which ones the klein arms require. I know the RPM team car replacement rear arms use the older, longer inner hinge pins...

Here's a long overdue update.

1. I got my powder coated chassis back, it appears as if they didn't remove the anodizing off the chassis, but it still looks good enough to be a runner. Can't complaint much, I only paid $25 bucks.

2. Used a counter sink tool to remove the coating from the holes and decided to counter sink a couple more holes.

3. I wasn't counting on cutting the chassis (not confident enough with the Dremel), but after mock mounting the body I decided to slam it. I think I did quite an OK job, not smooth like all other cars, but it works...

4. The bearings on the steering were worn out, so I decided to ghetto rig regular RC10 front wheel bearings to work with the steering. I cut down a pair of Losi XX front axles, used them as steering post, use some axle spacers to keep the bell cranks from sliding out, a couple of shims to keep it from binding, and voila.... new bearings and a silky smooth steering.

5. I used the RPM tranny brace and front bumper from the Ultra Molded Kit.

I still need the front hinge pins, which I ordered from Tower, along with a new set of Tie Rods, need to pull out the axles from my B44, mount the rear shocks, and paint and mount the body.

Here are some pictures, excuse the poor quality...

Any suggestions will be greatly appreciated.

Oh, I know one of the rear arms is mounted backwards.

Lookin' real nice! What did you end up figuring out on the rear inner hinge pins? It's hard to tell by the pic, but it looks like the klein arms might use the truck ones huh?

Sweet buggy all of these modern RC's are makeing me want one. SHHH (dont tell the Losi god's )

cyclepsych0 wrote:Lookin' real nice! What did you end up figuring out on the rear inner hinge pins? It's hard to tell by the pic, but it looks like the klein arms might use the truck ones huh?

They are a tad longer than needed, but they'll do the job just fine. I'm just waiting on the front ones to arrive.

whats the difference in the Klein arms verses the RPM ones?

Couldn't tell you Rick, I've never had the RPM ones, besides the different materials they're made out of.

Klein arms: Delrin
RPM arms: Non Delrin...

It's OK Freddie, I'll carry the Losi torch for you at the VONATS this year I got most of my racer put together last night, It's not a XX but I think you'll like it. I'm looking forward to racing against you again, we had some close battles last year!!

markt311 wrote:It's OK Freddie, I'll carry the Losi torch for you at the VONATS this year !!

Mark I wont be much compitition but I will be running my Losi also I should be just enough in the way to keep lap times down