RC10 Graphite Team car Oval style 91'

[Charlie don't surf]

This is exactly what I started racing oval with around 1990, when you were in the "novice" class you just threw some tires and an EDM body in it and you were good to go-when you got to the "advanced" class, you started making car improvements and got quicker and....you always starting dyeing everything black. Once you got to "expert" class, your car pretty much lookied like this-

1 a1 wallts car 001.jpg

Just needs an EDM body!

1 a1 wallts car 002.jpg

Andy's front end, trailing axle steering and Tecnacraft rods

1 a1 wallts car 003.jpg

Andy's rear arms with Rayborn slider conversion and Losi 2038 rear hubs. Robinson Racing 64p tranny internals and Losi 64p outer gear

1 a1 wallts car 004.jpg

New 6036 chassis, and wheels with some bling Proline waffle rears, Tamiya smoothie or Dynamite fronts

1 a1 wallts car 005.jpg

Houge steering--we used either the Houge bellcranks, or the A&L kit depending on the track conditions

1 a1 wallts car 007.jpg

Aluminum rims made by my buddy's dad in 89'--I need to put a good polish on these, then they will go on here-you had to be really cool at our track for Todd's dad to make these for you, I still don't know how I got em'

[m_vice]

Nice ride . I like the small rims and tires on this kind of cars. Very sharp .

[Dirtdiver]

Very nice.
Did you ever run Tamiya Lancia tires instead of Pro-line waffles?

[wyldbill]

you mean you guy's were not running GRAPHINATORS back then or were they more in the expert class. when i started in '92 that was the best low buck oval car to have.

[jdenison75]

those pro-line waffles are cool. especially with those rims .

[jwscab]

did you modify the outdrives on the stealth trans to accept the rayborn sliders? widen the groove, and drill a hole for the cross pin? neat. they are hardened, no? have to use a cobalt bit or something to get that hole in there?

[aconsola]

CDS, where did you race that?

[Charlie don't surf]

That is a car from Walt's Hobby in Syracuse NY, the outdrives are Moose Ti, so they slot easily- and the R&D terminators were brought up from the US Openwheel at Kranzels, but they ran like crap
until we figured out the setup so for a year and a half we ran about 3 laps faster than a Terminator
with this car. Then the B2 came out and it was faster in stock trim than this one was

[Asso_man!]

Were the 1.6" wheels better than the 2.0" for oval racing in 1991?

[Charlie don't surf]

Yes they had a lot of sidewall flex which enhances the traction on a slick track

[Dirtdiver]

So you never used Tamiya Lancia rear tires at Walt's old store?

[THEYTOOKMYTHUMB]

How hard are Andy's arms to find? I looked a while back with no luck. I didn't do any extensive research or anything, but I was surprised they didn't pop right up on ebay.

[shodog]

How hard are Andy's arms to find?

no not really. they are available at tower

http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXGAF4&P=7
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXEU95&P=7

[THEYTOOKMYTHUMB]

How hard are Andy's arms to find?

no not really. they are available at tower

http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXGAF4&P=7
http://www3.towerhobbies.com/cgi-bin/wti0001p?&I=LXEU95&P=7

Touche

[shodog]

Charlie, I am incredibly envious of your fresh chassis. Overall the buggy looks great