My first composite RC10 project

General discussion, builds/restorations, etc...

Moderators: scr8p, klavy69

Post Reply
User avatar
Synergy
Approved Member
Posts: 1787
Joined: Sat Dec 23, 2006 5:57 am
Location: North East England
Has thanked: 127 times
Been thanked: 70 times

My first composite RC10 project

Post by Synergy »

You guys make this project stuff look a lot easier than it is :oops: So this chassis hasn't got enough holes for a stealth so it must be fore a 6 gear tranny right :?: This body don't go around this chassis massive girth is there a one that will :?:. I look forward to all the laughing smilies but can you include some advice among the hysterics please :) :?
Attachments
Img_1066.jpg
Fat chassis
Img_1066.jpg (108.43 KiB) Viewed 1649 times
Fat chassis
Fat chassis
Img_1066.jpg (108.43 KiB) Viewed 1649 times
Img_1069.jpg
what happened to the holes?
Img_1069.jpg (132.74 KiB) Viewed 1649 times
what happened to the holes?
what happened to the holes?
Img_1069.jpg (132.74 KiB) Viewed 1649 times
Experience is that marvelous thing that enables you to recognize a mistake when you make it again.

Here's my TC Showroom
http://www.tamiyaclub.com/showroom.asp?id=18028
Top
User avatar
Sharkman
Approved Member
Posts: 161
Joined: Fri May 19, 2006 7:53 pm
Location: 150 miles south of Widdys place

Stealth Trans

Post by Sharkman »

ferretti,I'm assuming you have a Stealth for it. Some time ago,there was a metal template that AE made to drill the 6-gear chassis for Stealth trans. If you want to drill the chassis,maybe you have a Stealth chassis already drilled,make a small template of scrap G-10 or even lexan,and "be careful" thats a nice ride :wink:
Dan
Top
User avatar
Synergy
Approved Member
Posts: 1787
Joined: Sat Dec 23, 2006 5:57 am
Location: North East England
Has thanked: 127 times
Been thanked: 70 times

Post by Synergy »

Thanks Sharkman, the car came with a stealth that I wanted to use as I was considering running it in vintage competitions. I do have a couple of 6 gear trans I can put in it, I don't want to drill it I'm not that confident and I have seen a few properly messed up doing it.
Experience is that marvelous thing that enables you to recognize a mistake when you make it again.

Here's my TC Showroom
http://www.tamiyaclub.com/showroom.asp?id=18028
Top
badhoopty
Approved Member
Posts: 3753
Joined: Tue Feb 07, 2006 2:12 pm
Has thanked: 15 times
Been thanked: 35 times

Post by badhoopty »

an mip tranny would fit without drilling.
Top
User avatar
Synergy
Approved Member
Posts: 1787
Joined: Sat Dec 23, 2006 5:57 am
Location: North East England
Has thanked: 127 times
Been thanked: 70 times

Post by Synergy »

I think what I might do is strip this back down and integrate one of my 6010 cars into it as I planned and use this nice stealth car for the Tekin chassis that's on its way. :D
Experience is that marvelous thing that enables you to recognize a mistake when you make it again.

Here's my TC Showroom
http://www.tamiyaclub.com/showroom.asp?id=18028
Top
badhoopty
Approved Member
Posts: 3753
Joined: Tue Feb 07, 2006 2:12 pm
Has thanked: 15 times
Been thanked: 35 times

Post by badhoopty »

tell me you didnt spend over 50 bucks on the tekin chassis... :?
Top
User avatar
Synergy
Approved Member
Posts: 1787
Joined: Sat Dec 23, 2006 5:57 am
Location: North East England
Has thanked: 127 times
Been thanked: 70 times

Post by Synergy »

Awh that's nice of you Badhoopty thanks for the concern mate :) no I bought one straight from Tekin $30 plus shipping $54 in total. :D :D :D
Experience is that marvelous thing that enables you to recognize a mistake when you make it again.

Here's my TC Showroom
http://www.tamiyaclub.com/showroom.asp?id=18028
Top
badhoopty
Approved Member
Posts: 3753
Joined: Tue Feb 07, 2006 2:12 pm
Has thanked: 15 times
Been thanked: 35 times

Post by badhoopty »

right on. :wink:
Top
User avatar
ra272
Approved Member
Posts: 312
Joined: Fri Nov 17, 2006 9:32 am
Location: NANCY FRANCE
Been thanked: 7 times

Post by ra272 »

really nice car, I think it will look great with a black dyed 6 gears tranny.
Top
User avatar
Synergy
Approved Member
Posts: 1787
Joined: Sat Dec 23, 2006 5:57 am
Location: North East England
Has thanked: 127 times
Been thanked: 70 times

Post by Synergy »

Plans for this chassis have changed a bit. http://www.rc10talk.com/viewtopic.php?t=1146
Experience is that marvelous thing that enables you to recognize a mistake when you make it again.

Here's my TC Showroom
http://www.tamiyaclub.com/showroom.asp?id=18028
Top
Post Reply

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Register

Sign in

  • Similar Topics
    Replies
    Views
    Last post
  • New Composite Craft Project
    by RC10Sprinter » » in RC10 Buggy Forum
    23 Replies
    1798 Views
    Last post by bearrickster
  • My first reworked Composite project.
    by Synergy » » in RC10 Buggy Forum
    11 Replies
    1892 Views
    Last post by fastang
  • Composite chassis 6 gear buggy cleanup project
    by Frankentruck » » in RC10 Buggy Forum
    25 Replies
    1569 Views
    Last post by juicedcoupe
  • New Composite RC10 buggy.....
    by Md_RC10 » » in RC10 Buggy Forum
    4 Replies
    987 Views
    Last post by DaveM
  • rc10 ls composite craft
    by didou60110 » » in Associated On-Road Forum
    6 Replies
    2343 Views
    Last post by filou
  • Composite Craft Oval RC10
    by THEYTOOKMYTHUMB » » in RC10 Buggy Forum
    4 Replies
    548 Views
    Last post by rc10johnny
  • my worlds composite craft rc10 on a budget
    by hugger19 » » in RC10 Buggy Forum
    19 Replies
    4263 Views
    Last post by hugger19
  • Help with new build- Rc10 composite craft chassis
    by Wickedbass » » in RC10 Buggy Forum
    3 Replies
    237 Views
    Last post by Frankentruck

Return to “RC10 Buggy Forum”

Who is online

Users browsing this forum: No User AvatarGoogle Adsense [Bot] and 33 guests