Re: My RC10.2 build. (OIN)
Posted: Thu May 02, 2013 11:31 pm
Damn Sean!
RC10Talk - The Net's Largest Vintage R/C Community
My RC10.2 build. (OIN)
Page 7 of 13
Re: My RC10.2 build. (OIN)
Posted: Fri May 03, 2013 7:52 am
Wow!
Re: My RC10.2 build. (OIN)
Posted: Fri May 03, 2013 10:05 am
No, its a RPM RC10 gear cover.askbob wrote:Is that a B4 gear cover?
Re: My RC10.2 build. (OIN)
Posted: Fri May 03, 2013 10:18 am
Thats nice.
and i didnt quite know you had a paint scheme picked out already.
and i didnt quite know you had a paint scheme picked out already.
Re: My RC10.2 build. (OIN)
Posted: Fri May 03, 2013 11:54 am
Thanks everyone!
I will try to get pics of it mounted later.
On another note, I have decided that the shock tower is staying. With Big Bores you have to space the shock out on the top of the tower. This makes them stand up more and although the 2mm or so doesn't really look all that bad, I knew it and could see it. With the tower flipped, they are still spaced 2mm, but the shock is at a more natural angle in relation to the a-arm.
I will try to get pics of it mounted later.
On another note, I have decided that the shock tower is staying. With Big Bores you have to space the shock out on the top of the tower. This makes them stand up more and although the 2mm or so doesn't really look all that bad, I knew it and could see it. With the tower flipped, they are still spaced 2mm, but the shock is at a more natural angle in relation to the a-arm.
Re: My RC10.2 build. (OIN)
Posted: Fri May 03, 2013 3:22 pm
Body mounted:
Re: My RC10.2 build. (OIN)
Posted: Fri May 03, 2013 8:17 pm
As stated earlier Damm! Very very nice.
Re: My RC10.2 build. (OIN)
Posted: Fri May 03, 2013 8:56 pm
wow. love the paint job.
What are you going to be using for electronics?
What are you going to be using for electronics?
Re: My RC10.2 build. (OIN)
Posted: Fri May 03, 2013 11:25 pm
Sonic: the body is right against the back of the shock tower... Barely fit, had to force it a little. Lol. I'll have more pics later...
Norman: Futaba servo and Rx, not sure yet on ESC, either LRP Flow or Tekin Rs... Probably RS... Reedy motor.
Norman: Futaba servo and Rx, not sure yet on ESC, either LRP Flow or Tekin Rs... Probably RS... Reedy motor.
Re: My RC10.2 build. (OIN)
Posted: Sat May 04, 2013 11:56 am
great looking build Sean, let us know how it performs on the track.
if you get a chance too, can you post a pic of how you cut the body for the wing mounts to pass through? i hacked a square hole in mine, but sure it could have been done cleaner.
if you get a chance too, can you post a pic of how you cut the body for the wing mounts to pass through? i hacked a square hole in mine, but sure it could have been done cleaner.
Re: My RC10.2 build. (OIN)
Posted: Sat May 04, 2013 12:20 pm
Yes I would like to see that too. I'm not a fan of WOIN with the back half of the body aft of the rear shock tower removed, but I don't want to do the traditional wing tubes in the bulkhead either.JK Racing wrote:great looking build Sean, let us know how it performs on the track.
if you get a chance too, can you post a pic of how you cut the body for the wing mounts to pass through? i hacked a square hole in mine, but sure it could have been done cleaner.
Re: My RC10.2 build. (OIN)
Posted: Sat May 04, 2013 3:54 pm
I'm not sure if its cleaner than a square, it might be a little sturdier though? Maybe?
Re: My RC10.2 build. (OIN)
Posted: Sat May 04, 2013 4:08 pm
So I dug through some stuff and found a B3 tower... Still hoping for another, but I'm going to also make one.
I think it looks better,
I think it looks better,
Re: My RC10.2 build. (OIN)
Posted: Sat May 04, 2013 4:40 pm
Superb!
Re: My RC10.2 build. (OIN)
Posted: Sat May 04, 2013 7:55 pm
JK Racing wrote:great looking build Sean, let us know how it performs on the track.
if you get a chance too, can you post a pic of how you cut the body for the wing mounts to pass through? i hacked a square hole in mine, but sure it could have been done cleaner.
I cut an uneven square on mine. Easier to remove the body.