RC10Talk - The Net's Largest Vintage R/C Community

I tried this before but it's a couple 100 pages back so I'm trying it again with the new blood around here. Last time somebody mentioned it might be mugen 1/8 scale aluminum a arms but I could not really find anything on them.. figured that it would be easy with the upright configuration but I was wrong. Lol

klavy69 wrote: ↑Wed Feb 22, 2023 9:18 pm Long shot here. Gear...looks kinda like MIP but really could be anything. Any ideas?16771185290332557260472618843105.jpg16771185698674235257585242227343.jpg1677118629136397285128672467728.jpg
Thanx in advance
Todd

MIP 4wd front diff gear (part# SP-26)

@klavy69

Ofna 18993 Monster Pirate front suspension arms?

Phin wrote: ↑Wed Feb 22, 2023 4:22 pm

Phin wrote: ↑Sat Jan 05, 2019 6:09 pm Thanks for the clues on the boat parts.

Here's another part I haven't been able to ID....ball diff for something using dogboes/drive shafts with ~8mm hexes on the ends. It's metric, 12mm at the widest bit, then 8mm on the shaft, and 6mm for the ID of the diff rings.

#$%^ing finally! For 4 years I've been trying to ID this diff.


hwfrgdiff.jpg

Son of a....now I don't know again. They could also be parts from the Nodis Frog diff.

Phin wrote: ↑Thu Feb 23, 2023 12:39 am

Phin wrote: ↑Wed Feb 22, 2023 4:22 pm

Phin wrote: ↑Sat Jan 05, 2019 6:09 pm Thanks for the clues on the boat parts.

Here's another part I haven't been able to ID....ball diff for something using dogboes/drive shafts with ~8mm hexes on the ends. It's metric, 12mm at the widest bit, then 8mm on the shaft, and 6mm for the ID of the diff rings.

#$%^ing finally! For 4 years I've been trying to ID this diff.


hwfrgdiff.jpg

Son of a....now I don't know again. They could also be parts from the Nodis Frog diff.

nodisfrgdiff.jpg

Wasn’t that what the mag ad was selling -(couldn’t see a brand name), Subaru brat, frog, Blackfoot, monster bettle etc all had the same gear boxes after all , nodis may have had a dog bone out drive option as well as the standard hex bones.

Thorp did both the standard and dog bone options as well as full dog bone conversion sets

If the one you have doesn't have a tufnol (orange brown papery) gear, it's not the nodis setup, it's the other one.

Retro rc wrote: ↑Thu Feb 23, 2023 5:54 pm Wasn’t that what the mag ad was selling -(couldn’t see a brand name), Subaru brat, frog, Blackfoot, monster bettle etc all had the same gear boxes after all , nodis may have had a dog bone out drive option as well as the standard hex bones.

Thorp did both the standard and dog bone options as well as full dog bone conversion sets

The first ad was from Hobby World from Hong Kong. Nodis was from the UK. The first clipping came from a US mag advertisement, the second a "what's new" type column from a UK mag. Both are dated 1984.

What threw me off about the parts being for a Frog diff was that they needed 8mm ID bearings, while the stock Frog drive cups (and the Thorp diff) used 5mm ID bearings. Also lots of 1/8 cars used hex bones BITD. RC500 bones will work with this diff.

jwscab wrote: ↑Thu Feb 23, 2023 6:20 pm If the one you have doesn't have a tufnol(orange brown papery) gear, it's not the nodis setup, it's the other one.

Given the lot I got the parts in, it's very possible/likely that the tufnol gear, and pressure plates were missing. I also think there should be a thrust bearing involved.

Phin wrote: ↑Wed Feb 22, 2023 9:55 pm MIP 4wd front diff gear (part# SP-26)

Thank you sir!

Elkcycles wrote: ↑Wed Feb 22, 2023 10:52 pm @ klavy69

Ofna 18993 Monster Pirate front suspension arms?

Thank you. By the question mark it gives me a place to start.
Todd

There's a couple of mystery center plunger tools in my grab bag of tools. Any idea what these are for? I'm sure I need them, just don't know why yet.
.

The bottom one is a pin pusher for pushing pins out of Tamiya connectors. Top one appears to also be a release tool, possibly for the smaller pinned AMPS connectors like AE used

Thanks! These actually will be really handy!

GoMachV wrote: ↑Fri Feb 24, 2023 3:59 pm The bottom one is a pin pusher for pushing pins out of Tamiya connectors.

I have one of those, and never knew that was what it was used for..... thanks @GoMachV, much appreciated!

Incredible_Serious wrote: ↑Fri Feb 24, 2023 4:25 pm

GoMachV wrote: ↑Fri Feb 24, 2023 3:59 pm The bottom one is a pin pusher for pushing pins out of Tamiya connectors.

I have one of those, and never knew that was what it was used for..... thanks @ GoMachV, much appreciated!

Ditto!

- I remember a hobby shop owner had one when I was a kid, but I hadn't seen one in decades.