NIX91 Questions and Answers

[Asso_man!]

Any ideas about where the gold wing mounts come from on Masami's car? Never seen these before.

[Minisforever]

Asso_ man been searching for the same. Here's what I came up with so far. Looks to be a yokomo part from the the later 834b. Part number ZC-107h but looks like there was a production change on part as some point. PM me if you come up with any leads and I will do the same.


http://www.rc10talk.com/viewtopic.php?f=29&t=24261

[Asso_man!]

OK thanks, that's where I saw them once. According to teh thread you mention they should be part number ZD-107H, specific wing buttons for the WCS. Not easy to find I guess...

[Peakey]

Are these the rear wheels I need ?

[Minisforever]

Wheels look right, but it's always hard to tell by photo. Header card on wheels say 12mm offset. Hope that helps

[Asso_man!]

Are these the rear wheels I need ?

These are probably 2.2" where 2.1" were used in '91. The ones on Masami's car are the ROAR ones and have 4 holes in the middle. He also trimmed the outside lips (inner and outer) to get more side grip and lightened them with quite a lot of holes. Pics can be seen in the RC10 buggy forum sticky thread.

[aip47-2008]

OK thanks, that's where I saw them once. According to teh thread you mention they should be part number ZD-107H, specific wing buttons for the WCS. Not easy to find I guess...

Definitely the ZD-107H part number in websteves link, though there are picture's also showing these ZC-107H on his older 4wd.

[Minisforever]

Seriously Aaron is there a yokomo part you don't have?

Check link out, maybe I'm confused on part number
http://www.rc10talk.com/viewtopic.php?f=29&t=24261

I figured eventually I would have to cough up some big bucks and have them machined. Hey, If enough guys need these wing buttons maybe we can have a small batch machined and anodized?

[GoMachV]

I just got a text message from Kelly, he wants me to test fit the stealth buckles and pins to make sure they are 100%. He said actual part numbers will then be assigned so no more trying to explain what you are looking for. I'll update soon

[Asso_man!]

OK thanks, that's where I saw them once. According to teh thread you mention they should be part number ZD-107H, specific wing buttons for the WCS. Not easy to find I guess...

Definitely the ZD-107H part number in websteves link, though there are picture's also showing the ZC-107H on his older 4wd.

These are not the ones shown here: http://www.rc10talk.com/viewtopic.php?f=35&t=5500&start=105
They are gold as well but much taller with a extra basis at the top.
Could it be that you don't have that part? Lol

[aip47-2008]

OK thanks, that's where I saw them once. According to teh thread you mention they should be part number ZD-107H, specific wing buttons for the WCS. Not easy to find I guess...

Definitely the ZD-107H part number in websteves link, though there are picture's also showing the ZC-107H on his older 4wd.

These are not the ones shown here: http://www.rc10talk.com/viewtopic.php?f=35&t=5500&start=105
They are gold as well but much taller with a extra basis at the top.
Could it be that you don't have that part? Lol

Agreed!

[alien3t]

http://www.ebay.com/itm/Yokomo-ZD-107-Vintage-WCS-RC10-Team-Associated-Rare-Wing-Buttons-/121514533728?pt=Radio_Control_Parts_Accessories&hash=item1c4ad4a360

http://www.ebay.com/itm/Yokomo-ZD-107-Vintage-WCS-Wing-mount-kit-RC10-Team-Associated-/121514544972?pt=Radio_Control_Parts_Accessories&hash=item1c4ad4cf4c

these wing buttons

[ralphee]

Now thats cheap!

Lee

[DennisM]

http://www.ebay.com/itm/Yokomo-ZD-107-Vintage-WCS-RC10-Team-Associated-Rare-Wing-Buttons-/121514533728?pt=Radio_Control_Parts_Accessories&hash=item1c4ad4a360

http://www.ebay.com/itm/Yokomo-ZD-107-Vintage-WCS-Wing-mount-kit-RC10-Team-Associated-/121514544972?pt=Radio_Control_Parts_Accessories&hash=item1c4ad4cf4c

these wing buttons

I´ve got the zc-107h version and they seem to have a bigger diameter than the ones on Websteves Stealth pictures.
The ZD´s You´ve linked to, seem to have the same diameter as my ZC´s, ergo too big on the "shaft" part?

Mine could be 5,4 mm on the "shaft" part - the ones on the Stealth pictures could be 1mm thinner?

The lower part angled finish on the Stealth pictures seems to be different too?

Running changes in production?

[Minisforever]

Dennis at first I thought it could be just an optical illusion but I think your right. I just compared the two and the cylinder portion is defiantly a smaller diameter. Good eye Dennis