Re: 4WD RC10 project
Posted: Fri Feb 20, 2015 7:47 pm
I saw it on FB too. This is going to be super cool!!
RC10Talk - The Net's Largest Vintage R/C Community
Ten4: the 4WD RC10 project
Page 2 of 40
Re: 4WD RC10 project
Posted: Fri Feb 20, 2015 9:07 pm
WTF IS FB?
Re: 4WD RC10 project
Posted: Fri Feb 20, 2015 9:13 pm
just take it all $$$$$$$$$$ iam never going to save any money being on this site
iam never going to save any money being on this site Re: 4WD RC10 project
Posted: Fri Feb 20, 2015 10:14 pm
Agreed.hugger19 wrote:just take it all $$$$$$$$$$
Re: 4WD RC10 project
Posted: Fri Feb 20, 2015 10:21 pm
Cool stuff, can't wait to see more!
Re: 4WD RC10 project
Posted: Fri Feb 20, 2015 11:20 pm
It blows my mind at all the options technology has offered in just the short time between joining this forum and now. I never would have guessed the technology would come so far so fast. It seems like cheating.
Re: 4WD RC10 project
Posted: Fri Feb 20, 2015 11:35 pm
Will these be available in purple? 
Re: 4WD RC10 project
Posted: Fri Feb 20, 2015 11:41 pm
If you have to ask, you haven't been paying attention
Re: 4WD RC10 project
Posted: Fri Feb 20, 2015 11:44 pm
Re: 4WD RC10 project
Posted: Sat Feb 21, 2015 2:30 am
More...
Playing around with some concepts for a front shock tower. Jeff and i discussed tonight and we agree we would like to keep the tower in the stock location, i.e. behind the shocks, so it still looks like a "proper" RC10.
Just messing around, here's what I've come up with.
looks like it can clear the body nicely with a little more work (the body is sitting a little high in this picture).
I think if we tilt the transmission back an additional 15 degrees or so it will lower the top of it enough so the body can sit down all the way. The nose brace tubes could run through holes in the tower. The transmission could bolt to both the nose plate and the tower, making it pretty strong.
Playing around with some concepts for a front shock tower. Jeff and i discussed tonight and we agree we would like to keep the tower in the stock location, i.e. behind the shocks, so it still looks like a "proper" RC10.
Just messing around, here's what I've come up with.
looks like it can clear the body nicely with a little more work (the body is sitting a little high in this picture).
I think if we tilt the transmission back an additional 15 degrees or so it will lower the top of it enough so the body can sit down all the way. The nose brace tubes could run through holes in the tower. The transmission could bolt to both the nose plate and the tower, making it pretty strong.
Re: 4WD RC10 project
Posted: Sat Feb 21, 2015 8:45 am
When you tilt it back will it still clear the steering ??
Can't wait to see the final product
Can't wait to see the final product
Re: 4WD RC10 project
Posted: Sat Feb 21, 2015 9:02 am
That would be cool if you could keep it stock looking like you have it mocked up now. I am impressed that it is this far along already.
Re: 4WD RC10 project
Posted: Sat Feb 21, 2015 9:40 am
I'm sure we're going to have to make custom steering to fit everything up there, but it should be doable.
Re: 4WD RC10 project
Posted: Sat Feb 21, 2015 12:20 pm
The work everyone is doing using the 3D printer is simply amazing!
But you guys have left us all with a difficult decision on which car to build.
But you guys have left us all with a difficult decision on which car to build.
Re: 4WD RC10 project
Posted: Sun Feb 22, 2015 6:15 pm
How are you going to hold the front tranny in place to the shock tower.