Re: NIX91 Questions and Answers
Posted: Wed Oct 08, 2014 3:52 pm
Should now be there...
RC10Talk - The Net's Largest Vintage R/C Community
NIX91 Questions and Answers
Page 9 of 30
Re: NIX91 Questions and Answers
Posted: Wed Oct 08, 2014 6:13 pm
Awesome. Thank you sir! I got them ordered.
Re: NIX91 Questions and Answers
Posted: Sun Oct 12, 2014 5:07 pm
Mark and I knocked our heads together and this was the result:
Rear hub with ASC7935+ASC7933+ASC6906 bearing set and two camber link holes. Classic look obviously
This could be used in a rere-RC10WC also. CVA axle should fit in there...
Rear hub with ASC7935+ASC7933+ASC6906 bearing set and two camber link holes. Classic look obviously
This could be used in a rere-RC10WC also. CVA axle should fit in there...
Re: NIX91 Questions and Answers
Posted: Mon Oct 13, 2014 12:02 pm
looks good.
Re: NIX91 Questions and Answers
Posted: Tue Oct 14, 2014 2:45 am
hiya
can someone give me the length of the drive shaft (asc6370) im not sure what car this is from nor the haft shaft (asc6374) as per the exploded diagram a few pages back.
just trying to work out if I need to buy some or if I have them in parts (that don't have part numbers)
thanks
ed
can someone give me the length of the drive shaft (asc6370) im not sure what car this is from nor the haft shaft (asc6374) as per the exploded diagram a few pages back.
just trying to work out if I need to buy some or if I have them in parts (that don't have part numbers)
thanks
ed
Re: NIX91 Questions and Answers
Posted: Tue Oct 14, 2014 3:08 am
Got 56mm from pin to pin for dogbone #6370.
Re: NIX91 Questions and Answers
Posted: Tue Oct 14, 2014 3:17 am
thank you Niki
so would either of these be a good substute ?
http://www.amain.com/MIP-Associated-RC10-CVD-Kit/p169074
http://www.amain.com/Team-Associated-RC10-1-4-Axle-CVA-Set/p267630
ed
so would either of these be a good substute ?
http://www.amain.com/MIP-Associated-RC10-CVD-Kit/p169074
http://www.amain.com/Team-Associated-RC10-1-4-Axle-CVA-Set/p267630
ed
Re: NIX91 Questions and Answers
Posted: Tue Oct 14, 2014 3:51 am
If you planned it on 1/4" axles...
With CVA's you will probably hit arm. CVD's should be ok.
My test with MIP#1198 was perfect.
http://www.rc10talk.com/viewtopic.php?f=99&t=36419&start=45#p405825
-Niki-
With CVA's you will probably hit arm. CVD's should be ok.
My test with MIP#1198 was perfect.
http://www.rc10talk.com/viewtopic.php?f=99&t=36419&start=45#p405825
-Niki-
Re: NIX91 Questions and Answers
Posted: Tue Oct 14, 2014 4:29 am
I would like to use the 1/4 inch axels as I have the yokomo adaptors and wheels to put on them.
I have some original cvas from my rc10 graphite, that tests with both the original 6365, 1/4 inch ID bearing fine, I just needed to confirm that the drive shaft length
I don't think these versions are available any more either
I have some original cvas from my rc10 graphite, that tests with both the original 6365, 1/4 inch ID bearing fine, I just needed to confirm that the drive shaft length
I don't think these versions are available any more either
Re: NIX91 Questions and Answers
Posted: Tue Oct 14, 2014 5:27 am
I just got a confirmation from my friend:
MIP#1007 CVD-set drive shaft lenght match MIP#1198 CVD shaft lenght you can see in the middle here.
http://www.rc10talk.com/viewtopic.php?f=99&p=405825#p405825
MIP#1007 CVD-set drive shaft lenght match MIP#1198 CVD shaft lenght you can see in the middle here.
http://www.rc10talk.com/viewtopic.php?f=99&p=405825#p405825
Re: NIX91 Questions and Answers
Posted: Tue Oct 14, 2014 6:58 am
Awesome!
Thanks Niki I'll go shopping
Ed
Thanks Niki I'll go shopping
Ed
Re: NIX91 Questions and Answers
Posted: Tue Oct 14, 2014 4:10 pm
An I right in thinking the front springs you are using are YS-2F to go with YS-2R yes?
Re: NIX91 Questions and Answers
Posted: Tue Oct 14, 2014 4:16 pm
yup, the copper springs...
like hens teeth those!!
ed
like hens teeth those!!
ed
Re: NIX91 Questions and Answers
Posted: Tue Oct 14, 2014 4:20 pm
Thank you 
Re: NIX91 Questions and Answers
Posted: Tue Oct 14, 2014 5:12 pm
just a suggestion. but if you're not building a masami replica, and something else those yokomo rear springs are not necessary. along with the yokomo shock spacers. you could build a stealth buggy like some of the other team member's buggies. it'll save you and your wallet the headache of searching for those items.