I picked up a Factory Team B3 off eBay last month... car was in worse condition than what I was expecting and I'm sure I overpaid, but after recently building a Factory Team B3 piece by piece with all NIP parts, this one seemed reasonable.
I was looking for a B3 i could use as my everyday runner and this one seemed to fit the bill. Luckily I have quite a collection of B3 parts laying around so I was able to rebuild the entire car using some good used parts as well as a few new ones. The only things I ended up reusing from the original purchase were the chassis, front kick plate, shocks, trans brace, turnbuckles, and CVD's. Everything else came from my pile of extras. I think I'll go with a new brushless/LiPo set up with this one.
If this is the one that had that corvette body on it you did just fine pricewise. That aluminum rear bulkhead brace would've cost you half of what you paid for the car on its own...used! I had that corvette b3 on my watchlist 3 times relisted I think and if I had the extra disposable income it would be here on the board in a f/s thread...minus the turnbuckles and rear brace I actually had a bid on it the last time but then decided before hitting enter I just didn't have the $ at the time.
The b3 has been a favorite runner of mine for a long time. It'll make a great runner for you.
Todd
Peace and professionlism.....Kabunga signing off!!!
klavy69 wrote:If this is the one that had that corvette body on it you did just fine pricewise. That aluminum rear bulkhead brace would've cost you half of what you paid for the car on its own...used! I had that corvette b3 on my watchlist 3 times relisted I think and if I had the extra disposable income it would be here on the board in a f/s thread...minus the turnbuckles and rear brace I actually had a bid on it the last time but then decided before hitting enter I just didn't have the $ at the time.
The b3 has been a favorite runner of mine for a long time. It'll make a great runner for you.
Todd
This is actually a different one, but I'm familiar with the one you mentioned. I sent an offer on the Corvette bodied B3 when it was originally listed and the seller counter offered. I passed on it tho. Then this one came up right after. The price was about the same, I ended up paying about $10 more for this one. The Racer's Edge trans brace was a nice touch Can't wait to put some electronics in this thing and test it out!
at $10 more for this one you still did OK with price IMHO. I sent an offer on that corvette bodied one too. Threw a lowball offer to him with a note to let me know what his bottom dollar was if he couldn't do my offer...he dropped $4 ...I passed also but was really jonesing for that rear brace but just couldn't justify it while I'm trying to put some $ together for a carbon fiber tub rc10t I'm trying to buy. Oh well, there will be more
Todd
Peace and professionlism.....Kabunga signing off!!!
Nice car, I love my B3 Amazed by how well they still drive by todays standards. Are you going to change anything on it, or modernize anything? I just did the typical b4 upgrades to make running it more viable.
sammydavisjnr wrote:Nice car, I love my B3 Amazed by how well they still drive by todays standards. Are you going to change anything on it, or modernize anything? I just did the typical b4 upgrades to make running it more viable.
I installed the B4 top shaft and slipper... that's about all for now
Well, I'm revisiting another old project here. Decided to convert my B3 FT car to a carbon fiber chassis. I ordered a NIX B2/B3 chassis from Fibre-Lyte and some parts from Shapeways. It took me just a short time today to swap everything over to the new chassis. I had to drill the chassis to secure the B44 saddle pack battery tray and drill a new hole to move the antennae mount to the front. I'm waiting on a few parts. I'd actually like to try this out at the local track in 2019....
Looking for any help sourcing factory team shocks for a T4 team truck build. Can be either the old 1.02 front and 1.39 rear shocks or the most recent 12x27.5mm and 12x36mm shocks. Is there anywhere FT shock kits can be bought? Or is the only way to...
Last post
...12x27.5mm and 12x36mm shocks. ...
And what the heck is up with AE discontinuing big bore shock kits, which they still sell with many of their kits?
at least one of the sets exist
the kashima coat bodies are pretty cheap online so a set can...
Got this a while ago been kinda working on it little by little. Has a brand new chassis plate and some other new stuff! Just need to get a few little things and a body then it will be ready to run.
I just happened on a t3/b3 chassis and Im thinking about building it. I read where they can still be competitive. Are the transmissions good enough for racing or should I change it out? The reason I asked I pull this trans apart and it was all metal...
Last post
The inners might work, I see e-clips. Still though, they have copies of Asso's molds so the dia of the hole in the arms may in fact be the same? :?
Here are some pics of my rc10t Ft I'm trying to find diff parts!, so I can race this in the vintage race at my local Track.
Last post
You can get all the parts for the Stealth transmision in your truck from a lot of places,eBay stores are good-try Trends & Trains (Jasminations,on ebay),Atomic on eBay...What do you need?
These trannys are bullet proof,when I got my T2,the guy I...
Until now, my newest AE vehicle was my GT, but I've been thinking I might get back into racing a little bit. I have three good tracks within an hour of me and a well maintained private track a block away. This truck popped up on craigslist today and...
Last post
The price on that thing was a steal! I've noticed parts seem more brittle and cheap compared to back in the day as well, I guess that is just how things go right? Great job on hte paint! Those relief cuts are very interesting looking! Glad it works,...
I recently finished this car so I figured I'd post up some pics for you guys to check out. I unfortunately have to sell off most of my collection to pay bills, so this car is for sale. Almost everything on this car is new and never run. It has all...
I actually had a bid on it the last time but then decided before hitting enter I just didn't have the $ at the time.
Can't wait to put some electronics in this thing and test it out!
...I passed also but was really jonesing for that rear brace but just couldn't justify it while I'm trying to put some $ together for a carbon fiber tub rc10t I'm trying to buy. Oh well, there will be more 
