I received this from the mailman today. I have a problem with the bell crank thou. I need the one for an RC10 either stock or aftermarket part will work for me. Used ok. And a rear shock tower to go with that. And also, I'll be needding a balack tub. The previous owner of this poor little thing sand blasted the chassis so now it looks awful.
Not bad isn't it. The MIP rear shocks are working smoothly as well. This car will surely see the tracks and I'll be racing it.
Nice find qctires... I had my eye on that auction too. My best ebay deals usually come with bad pictures. If I recall, there was only one fuzzy picture for this auction. I bet the cvds were a nice surprise.
Asso_man! wrote:that chsassis could look very nice after sanding and polishing it... if you won't use it, I could be interested
Actually, I am really planning to use my TQ10 chassis and just cut the front end to install the RC10T nose plate. I think it will look even better, all being black in color. What ya think?
I will glass blast the chassis tomorrow and see how it looks.
Hey qctires, you got two really nice platforms there. I'd just make two runners out of them. No need for any hack or slash'in or combining them, but it's all good!
carloco8 wrote:Hey qctires, you got two really nice platforms there. I'd just make two runners out of them. No need for any hack or slash'in or combining them, but it's all good!
Well, that wont be possible...look.
Attachments
2006_1026(006).JPG (126.97 KiB) Viewed 2855 times
2006_1026(006).JPG (126.97 KiB) Viewed 2855 times
I've cut the front end of the chassis to fit the nose plate.
2006_1026(003).JPG (130.22 KiB) Viewed 2855 times
I've cut the front end of the chassis to fit the nose plate.
2006_1026(003).JPG (130.22 KiB) Viewed 2855 times
Had to drill holes and counter-sunk them to install the stealth tranny.
2006_1026(004).JPG (139.39 KiB) Viewed 2856 times
Had to drill holes and counter-sunk them to install the stealth tranny.
2006_1026(004).JPG (139.39 KiB) Viewed 2856 times
Looking for longer tubes to fit the tube holders and looking for a bell crank. I wnt to trade for another one. This is an MIP unit for a 10T.
2006_1026(008).JPG (147.14 KiB) Viewed 2856 times
Looking for longer tubes to fit the tube holders and looking for a bell crank. I wnt to trade for another one. This is an MIP unit for a 10T.
carloco8 wrote:I would just leave the nose tubes off. The chassis and front plate screwed together should be sturdy enough.
It will need a bit of help from the tubes beacause somehow, it has a bit of movement. The wholem chassis will be flexing and the way I see it, it even needs some support on the rear bulkhead as well.
This car will see soil and a bit of racing and will not be on the shelf. I have my B4 ready but I want to see how the old one will fair.
Hey qctires where do you run your cars? Socal? HotRod? Revalation, Pegasus? I've ran my B4/T4 at all these places, but I'll only run my old RC10's at Socal, as their are no 1/8 scale gas cars to get hacked by, seriously!
Revelayion and Pegasus. I live close to the Sun Valley track but I don't feel confortable being there. Hot Rod, tried it twice last summer, couldn't stand the heat. And no shade nor chairs. The best still is Revelation. Just make sure you mlet the 8th scales go by.
Thought i would share some pics of my rc10.
I actually got given this for free with a joblot of schumacher stuff.
Been told this has the rpm worlds conversion? Any other info you guys can supply me will be greatly recieved.
Last post
Killer score. I still have a lightly used RPM kit that I need to put on a buggy one of these days. Still looking for the right chassis....
I bought the lot shown in the picture a while back from Ed (Dr. Robotnik) and was all ready to begin a rebuild--new build with these parts and parts I already have but I realized this wasn't what I thought it was...So...can Ed or anyone please tell...
Last post
You better check THIS out. I ordered a pair myself. together with the dynotech rear wheels you're set.
got bored today, snapped some pics of a couple projects that are pretty much done.
first is a rpm ultra-molded chassis conversion for the rc10.
full-on rpm besides the trans, i keep forgetting to order a rpm trans for it as well as a b2 body that...
Last post
Thanks Hoopty... I'll pass by one of the LHS here and check out their Trinity wheels.
Nearing a vintage race I've decided to dust off an old build of mine and let it stretch its legs. I've not posted this car before so even if it is an old and to this forum a fairly plain build, I throw it in here.
At first I could not remember...
A all new complete RC10 Composite Craft / RPM World 1991 , I had an Hydradrive and the Yokomo wheel adapter 8)
On this one I use a Houge Enterprise steering system !