
A peek into the Harris garage
- Bormac
- Approved Member
- Posts: 3113
- Joined: Wed Sep 05, 2007 3:52 pm
- Location: CENTRAL COAST, NSW AUSTRALIA
- Has thanked: 21 times
- Been thanked: 11 times
Re: A peek into the Harris garage
Great results Jeff. Your cars are stunning and have a purpose. Awesome! 

- Ruffy
- Approved Member
- Posts: 876
- Joined: Mon Jan 11, 2010 6:49 pm
- Location: Orlando, Florida
- Been thanked: 55 times
Re: A peek into the Harris garage
I can tell everyone, I have seen these cars in person and they are spectacular in person. The ano-job done on them is amazing, and they are all built for racing.
Great thread Jeff!
Great thread Jeff!
- murphy3428
- Approved Member
- Posts: 579
- Joined: Mon Oct 06, 2008 11:19 am
- Been thanked: 2 times
Re: A peek into the Harris garage
Hey Jeff that purple RC10 is sweet and the pro is comming along great are those the new parts from the first batch, looks like I better get off my butt and get started on mine.
- JHarris
- Approved Member
- Posts: 526
- Joined: Sat Jan 16, 2010 11:17 am
- Location: Orlando, Florida
- Been thanked: 2 times
- JHarris
- Approved Member
- Posts: 526
- Joined: Sat Jan 16, 2010 11:17 am
- Location: Orlando, Florida
- Been thanked: 2 times
Re: A peek into the Harris garage
Here's the cars I ran at the worlds in 2003. The B4 was raced up until about 6 months ago. I swapped the graphite chassis I ran in '03 for a plastic chassis and raced that car until I bought my new B4 in October. Then my 12yr old raced it until I finally decided to put the correct chassis back with it and put it on a shelf about 6 weeks ago. The setup is exactly the way I ran it then.
- JHarris
- Approved Member
- Posts: 526
- Joined: Sat Jan 16, 2010 11:17 am
- Location: Orlando, Florida
- Been thanked: 2 times
Re: A peek into the Harris garage
I've had some questions about the anodizing and hard anodize. Below is how the car starts out, after it's cleaned. This one was absolutely disgusting when I got it. I soaked it, scrubbed it and then stuck the pieces in the dishwasher! Once it's in pieces like this I will figure out what color I am going to go with and start getting all the parts for anodizing together. The black car is one I'm working on for my oldest. It was just done in hard black anodize.
- JHarris
- Approved Member
- Posts: 526
- Joined: Sat Jan 16, 2010 11:17 am
- Location: Orlando, Florida
- Been thanked: 2 times
Re: A peek into the Harris garage
Jeff-
Thank-you for sharing the photos of your cars. What additional information can you tell us about your IFMAR Medallion? Is there a logo or writing on the backside?
Thank-you
dirtdiver
Thank-you for sharing the photos of your cars. What additional information can you tell us about your IFMAR Medallion? Is there a logo or writing on the backside?
Thank-you
dirtdiver
- rc10johnny
- Approved Member
- Posts: 1310
- Joined: Sun Sep 27, 2009 6:48 pm
- Location: Richmond Va.
- Been thanked: 1 time
- JHarris
- Approved Member
- Posts: 526
- Joined: Sat Jan 16, 2010 11:17 am
- Location: Orlando, Florida
- Been thanked: 2 times
Re: A peek into the Harris garage
Here are photos of the front and back. This is the case they gave them to us in.Dirtdiver wrote:Jeff-
Thank-you for sharing the photos of your cars. What additional information can you tell us about your IFMAR Medallion? Is there a logo or writing on the backside?
Thank-you
dirtdiver
- Chip from GA
- Regular Member
- Posts: 2
- Joined: Fri Apr 09, 2010 8:57 am
Re: A peek into the Harris garage
Awesome pics Jeff!! That is some amayzing work you are doing.
BTW: now my wife wants a brick driveway!
Thanks a lot!!! 
BTW: now my wife wants a brick driveway!


- Chip from GA
- Regular Member
- Posts: 2
- Joined: Fri Apr 09, 2010 8:57 am
Re: A peek into the Harris garage
Great Job Jeff!
How did you secure the battery strap to the rear bulkhead of your Team Car? Did you have to trim any of the Bulkhead for a li-po to fit? Could you take a pic of how the strap attaches to the bulkhead?

How did you secure the battery strap to the rear bulkhead of your Team Car? Did you have to trim any of the Bulkhead for a li-po to fit? Could you take a pic of how the strap attaches to the bulkhead?
Re: A peek into the Harris garage
Did you use a B4 transmission top shaft in the Team Car transmission? What non Team Car parts did you use?
Create an account or sign in to join the discussion
You need to be a member in order to post a reply
Create an account
Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute
Sign in
-
- Similar Topics
- Replies
- Views
- Last post
-
- 35 Replies
- 5045 Views
-
Last post by Asso_man!
-
- 13 Replies
- 1855 Views
-
Last post by mAdMan
-
- 56 Replies
- 8183 Views
-
Last post by orangemazda
-
- 34 Replies
- 6405 Views
-
Last post by Lavigna
-
- 51 Replies
- 7374 Views
-
Last post by Hcp22
-
- 58 Replies
- 7799 Views
-
Last post by jcwrks
-
- 33 Replies
- 3577 Views
-
Last post by lexus-5
-
- 12 Replies
- 6790 Views
-
Last post by TM Ru22311
Who is online
Users browsing this forum: Amazon [Bot] and 4 guests