I have strated on the chassis and this thing is in rough shape. I never realized how bad the aluminum was from associated. I guess I was expecting a somewhat smooth chassis, but this thing is full of pits. I snapped some photos of the side of the tub where you can see exactly what I am talking about.
I am just about done with the motorplate and took a picture to show the end result. The motor plate will be machined in a couple spots to loose some material. If everything goes as planned, I hope to be ready for anodizing this weekend. It is quite a bit of work to get the aluminum as smooth as the motor plate, but it looks sooooooo much better than the moon surface I started with. I was dreaming thinking 400 grit would get the aluminum smooth. I am having to start with 100 grit and make several passes before moving up to 400 grit.
AE chassies never went out from the factory like that, I bet it's more the chemical substance the previous owner used to try and remove the ano from the tub that attacked the aluminum surface and made it look like a teenager face skin.
_____________________________________________
_____________________________________________
Come and visit the stable
That is probably pitting from oven cleaner which is typically used to strip anodizing. It works fast and you've got to time it right to keep that from happening. Another thing that will pit it like that is trying to use a wire wheel on it.
I agree with RedScampi, judging from the way the material is "pulled" around the one hole, and around the edge of the tub I would deifnitely say wire wheel. I have a chassis that looked like it was a nice straight chassis, before someone did that to it....
I hear you on the 100 grit. I have a 4 inch DA sander that makes really quick work on the chassis but I have to change sanding pads quite often. I got one of the sides done last night and man what a difference. I need to pick up some more 400 grit to get all the swirl marks out of the aluminum. I am going out tomorrow to find another DA sander that will take 2 inch pads so I can get inside the tub. That is going to be the most difficult part about this build. You guys should be surprised with the outcome after seeing the shape this thing was in.
I got most of the chassis done now, and man was this thing a pain in the butt. It is not perfect but ten times better than it was. I may end up needing to bead blast the inside of the tub. I cannot get to a few samll areas. I did the machine work on the motor plate and the nose plate. I am probably going to break down and buy another nose plate for the car. I really hate that someone drilled a hole in the top center of the AE logo. The nose plate did not turn out like I wanted it to. I had to round the corners because there were extra holes drilled in the corners. Enjoy the pics, I hope to get the parts prepped for the anodizing process early this week and get going on other parts of the car.
Anodized the aluminum today and the efforts ended in utter failure
I got good coverage on the motor plate, but the nose plate and chassis has a really crazy looking finish to it. The bottom of the chassis looks like the sky on a clear evening where you can see all the stars. I will post some pics later. I am going to have to take another stab at it later. The green is really ugly anway so back to the drawing board on this one.
dunno what you are using for a power supply, but you might need more juice for the large area of the chassis/nose in order to get a solid anodized layer.
Typically, the more surface area you are trying to anodize, the more amperage you need. Small parts like shock caps and bushings are easy, large parts like a chassis... not so easy. Google some "home anodizing" setups, and you should be able to find equations for amperage vs. square inches (dont' forget to use both sides of the aluminum chassis when calcualting surface area ). -Jeff
I think I am getting pretty good juice flowing. I am using a charger caple of up to 250 amps. The lowest setting I can run is 50 amps and it really gets the acid flowing. It was pretty chilly today and the I had to start adding ice to the acid to cool it during the process so I didn't burn the aluminum.
I had four leads going into the chassis for the reason you stated, large area to cover. The sides of the chassis took the color very good, just the inside of the tub and the bottom of the tub came out wierd looking.
Where to start... so back in the late 90s I had no driver license or car, but I did have a few boxes of hand me down RC stuff from the 80s and a box of RCCA from that period as well. First car was a Kyosho Raider, but I always wanted a RC10, Ended...
Last post
Nice Car. Nice job. Now it won't be long before you tweak another one for your stable. 8)
About that.... I been casually looking at early gold chassis cars on and off. But last night picked up a B3 Team car, too good a deal, could not pass it up...
All of the truck parts are in good condition and I have started the cleaning process. Parts will be dyed black. Tons of dirt and grease build up. Chassis is fairly unmolested and is going to be...
Last post
i gotta think red rit dye should penetrate, just use like 2-3 packages of it so its SUPER red with little water and heat that water up. let it soak for a few days. Ive dyed white fiberglass black with rit dye without any problems, takes the dye in...
Well, I picked up my first RC10 today and wow, this is gonna be some serious work. The chassis is severely bent along with the nose piece. The rest of it appears to be in decent shape though. The front arms a bit beat up but the shocks look pretty...
Last post
very nice clean up of the rc10, top work 8) enjoy driving it!
well wrapped my tub chassis collection up today with a nitro ds , but after posting my collection up i am shy a actual gold tub
( check out the gallery here )
so i busted out the parts baggies and after a bit of digging i came up with this...
I have an odd request. Does anyone have any exploded diagrams of the B5 & B5M? I got 2 boxes of parts in a trade, and I was told it's B3/T3, B5 & B5M stuff. I feel I have all the B/T3 stuff removed. I'm trying to sort the B5M/B5 stuff. I'd really...
I had this car that I got off ebag as an impulse buy. since i've been collecting Losi's like a madman lately I decided to let my wallet cool off and try to make something out of this car. My ground rules I set for myself were that I had to build it...
Last post
Thanks guys. I had to be selective about the photos I posted because I made the mistake of putting the silver down before I decided to paint the sides red. I had some red speckles in the silver in a few places. Rookie mistake. :oops: Good thinking...
I found this Worlds Car on the local Craigslist. What a basket case. Does anyone see anything funny? Since it needs new arms and nose tubes, I was thinking about finally getting some Dynatech arms and converting over the front end. This ones gonna...
Last post
looks like a team car with worlds pieces, explains the u joints, 2.0 rear wheels and non machined chassis tub.
thought the worlds car came with u joint driveshafts?
As Bormac may have mentioned we have a vintaqe enduro on here in Australia this weekend. I decided to try something different and pulled this junker I got for 21 Pounds from the UK out. Now the car wasnt pretty at all with tonne of grease...
Last post
Darryn, she looks a treat indeed. I've decided on a JRX2 as my next project as soon as the Team Car's done.
Just an FYI, you column in the back of R/C Car is the only reason I buy a copy every month. Those articles are why I got into collecting and...