RC10Talk - The Net's Largest Vintage R/C Community

Friday I finally got my new project in. The previous owner must have really liked Miller. https://i.postimg.cc/DSQMfQDG/efafafafa.jpg https://i.postimg.cc/v132fYGH/efeaefefea.jpg https://i.postimg.cc/5XWrMKP1/ergervaewe.jpg https://i.postimg.cc/1fqd21rJ/rgrwgawffvas.jpg https://i.postimg.cc/kVnh263p...

Looks sweet! How are you mounting the batteries? I just did a design for mine to mount a single shorty lipo if you need inspiration.

Few small updates. I ended up purchasing a ebay lot earlier which includes a full LXT, some XX and XXX parts and chassis and what I hope is a JRX2 chassis as well as a load of parts so excited to see that come in this weekend. I ended up getting my carbon towers from Vintage R/C. I bought all 3 JRX ...

Lavigna wrote: ↑Fri Oct 07, 2022 6:58 pm JC Racing wheels and Schumacher rubber has been installed. Still working on the stance, and a few other things to come. Comments always welcome.

Never seen those before they look sharp though! I need to see if I can get those I just noticed they have JRX2 wheels too!

She's a runner now. The electronics layout isn't pretty, mostly becuase I have the battery adapter cable and lipo voltage monitor that i use to run on my older electronics. The Futaba ESC is pretty damn nice. need to do some swapping of tires and such before I run it on a track. I found that JC Raci...

I've done PLA+ and PETG both look good like Dean had experienced but they don't last long. I haven't revisited ABS yet because I'm too lazy to swap filament right now.

Not much to report.I replaced the super loose rear ballcups with some I had in an old pit box and drove it for a bit at the local indoor carpet offroad track. https://i.postimg.cc/JyjtJ0ww/IMG-20221009-193118028.jpg https://i.postimg.cc/gxCnnRTq/IMG-20221009-195449222.jpg https://i.postimg.cc/WdFdNS...

Nylon is more durable than ABS. I wouldn't bother with ABS. I need to upgrade the printer before I can really do nylon. It's something I have been looking into though. Really though I want to eventually get a 2nd printer so I don't have to constantly change setups to work with different filament ty...

I got a surprise early delivery today from over the pond by JC Racing

got my order of JRX2 wheels from JC Racing (and a set of spoked XX-4 wheels) and decided to mount up the tires. Really liking the look. Really need my new body now.

I have both cars. As far as the Chassis itself goes the only real difference is 13mm in length. All this length is aft of the rear pivot mounts. Pictures for reference, note that they aren't perfect. https://i.postimg.cc/dkQcHRV4/IMG-20221030-181913892.jpg https://i.postimg.cc/KKDyDpx1/IMG-20221030-...

So the first ever "Hobby grade" RC I owned was a used Losi JRX Pro SE that my step father helped me purchase when I was a kid. Later I sold it off to help buy a a former racer's LXT and his entire inventory of parts, radios, electronics, and motors, batteries ect. This was decades ago but ...

The manual calls out A-1012 for the "front Pro axles" (used on the LXT, JRX Pro SE, and GTX) you may have the JRX ones, A-1005, Which I think might be slightly shorter. Do they have a Set screw in the back? How sure are you that those are the right spacers? They should be thinner than the ...

HS-YZ250 wrote: ↑Tue Nov 08, 2022 10:41 pm As a tangent, I was wondering if XXX SCT CV axles would fit on an LXT w/XX Retrofit transmission. Mine has the LRM so it probably won't work.

They won't. The XXXT has a much longer CV shaft.

You are not authorised to read this forum.