RC10Talk - The Net's Largest Vintage R/C Community

I saw this card on ebay

Ebay link
I got as far as finding this

https://www.comc.com/Brands/Non-Sports/1992/Masters_of_RC_Auto_Racing

It appears to be a 155 card set of rc related cards similar to 1:1 racing cards. Does anyone have a set and a few pictures?

So, I've been making progress getting my Team Edition carbon chassis RC10 back together. I got an 81 tooth spur gear on the way. Can anyone recommend a pinion size for use with a 4-pole 4300 kv motor on 2S? Thanks! It's going to be temperature and surface dependent. If you are running on a dry flat...

A while ago I bought a cut down and cracked graphite chassis off ebay. graphiteDamage.jpg damage2.jpg damage4.jpg I though this was a good change to learn how to do proper carbon fiber repair since I have should have everything needed to do it. The laminated layers split. I cut a groove in the top l...

Mwildmann wrote: ↑Thu Apr 06, 2023 7:28 pm
Anyone know offhand with the inside diameter is of the early RC-10 shocks, 12mm? Look for something 13 or 13.5mm in diameter to cut a little wedge out of.

.4" /10.2 mm is the inner size of vintage associated small bore shocks.

Thanks for winning that. I really didn't need a third.

Once more try on the rpm style 8090 style chassis. Armed with a bit of experience. A89D74E4-01DA-44AE-9AD0-002425CBFF82.jpeg Wrapped in aluminum over clay. All the flat areas were built out with clay. I applied the foil with spray adhesive leading to a slight bumpy surface. I burnished down the foil...

I wasn’t the other bidder but I was looking at it until the last. It was a good looking t2 and I have a soft spot for them. Gotcha. They are way cool. My brother has an RC10GT and a truck converted RC10 buggy, I think an RC10DS also, I have the Team Car that I'm still finishing, and my daughter has...

Most of the results actually looked like cars, this one was special though.

Not even sure what to do with these, needed arms for a runner and these popped up.

Questions for you all 1) How bad is it to not have a differential? Has anybody else tried adapting one of these truck transmissions to work with a buggy before? 2) I'd like to ideally run this on a 4s Lifepo4 battery (so 14.4V). Is this too much? Should I aim lower? 3) What motor would you guys rec...

I prepped the mold, washed and waxed with putty put in every edge or defect. I then made a pattern. I applied some spray adhesive for the carbon fiber to stay cohesive. note: Back fabric patterns with cardboard or poster board. 65C35C09-4BC9-47E7-BA96-FDCA5FC7DFF1.jpeg 92FF4768-3098-4DD7-BE82-B26859...

Great result. Notes: This build hit 2.1mm. Target 3.0 mm for flat chassis. 2.1 for tub style chassis. The resin saturation was good and very few pinholes I wonder if I revered the resin to epoxy ratio in my notes. Note: Having consistent resin issues. D03EA9DD-EF4E-4EFB-BABF-96C4AC79E1C5.jpeg Unbagg...

Found someone to talk for help on molding parts. This was the shop decoration.

Well that worked AB2A4279-51CB-45F7-959E-2E3819CA2190.jpeg Full demold no damage 4951E4CE-BABB-42E9-B652-A8F9D215BA10.jpeg Bottom 8804F906-457B-43D5-9D80-B490DAB144F4.jpeg Inside 60D73434-1B0D-407B-8689-21D3A113F19F.jpeg The vacuum failed on readiest bag. I think the chemicals from the process make ...

This is requiring a lot of finishing. 28BEE05C-F1CA-40FF-A91F-098ABE46915F.jpeg I will add a few layers of material from the rear bulkhead back to make rear about 3.0 mm and thicker overall. I plan for it to sit under suspension components. I was using a rotary tool, but it seems I can use tin snips...