Search found 283 matches
- Wed Aug 09, 2023 10:19 am
- Jump to forum
- Jump to topic
Re: So, what did you do RC today?
Painted the Schkee body on my Bolink Eliminator. Some paint boo boos here and there, but nothing that can’t be covered up by decals (plus, I’m going to run it). I had Nathaneal at MCI print me a custom sheet of fictional liveries that should be here today. It’s now got a Hobbywing 1060, Reedy motor,...
- Thu Aug 10, 2023 2:11 pm
- Jump to forum
- Jump to topic
Re: So, what did you do RC today?
Now to finish the decals on the right side.
Nathaneal at MCI did an AMAZING job! The colors are gorgeous
Nathaneal at MCI did an AMAZING job! The colors are gorgeous
- Sun Aug 13, 2023 1:48 pm
- Jump to forum
- Jump to topic
Lightz Oval Conversion
It's been a while since I built an RC10. So I figured it was finally time to open a NIP Lightz oval conversion I've had for many years. There's nothing fancy on this one and I built it as more of a gearbox club racer. - Lightz oval conversion chassis - RPM 1.96 Stealth conversion - Barracuda slipper...
- Thu Aug 17, 2023 6:25 am
- Jump to forum
- Jump to topic
Re: Again another Marui project : Super Wheelie and Big Bear!
I will need to print body accessories for my almost fully printed model... I started to put the roll cage parts together with joints to be able to prepare the clusters... https://i.imgur.com/gBXIgfu.jpg Then I added all the accessories for the Super Wheelie bodies. The front part of the spare wheel ...
- Fri Aug 18, 2023 4:23 am
- Jump to forum
- Jump to topic
Re: So what did you get in the post today ???
Some prints arrived today...
Most of the chassis parts for my Super Wheelie project and a lighter Idle gear for my Hunter...
Most of the chassis parts for my Super Wheelie project and a lighter Idle gear for my Hunter...
- Sat Aug 19, 2023 1:31 pm
- Jump to forum
- Jump to topic
Re: Lightz Oval Conversion
I made a few changes and added some electronics to finish things up: - Bud's front arm brace - Swenton Racing extended motor plate - Hard anodized Team shocks - Factory Works Ah Cool Things washers & aluminum screws - Hyperdrive belt setup - Tekin 410K - Futaba S9101 & FP-R103F - Wimpy mod m...
- Sat Aug 19, 2023 2:07 pm
- Jump to forum
- Jump to topic
Re: So, what did you do RC today?
Made a road trip to pick up a lot.
- Sat Aug 19, 2023 4:18 pm
- Jump to forum
- Jump to topic
Re: So, what did you do RC today?
Monogram (Bandai) Mad Wolf
Very interesting kit. If I didn't hate resizing all my pics I'd start a thread.
Very interesting kit. If I didn't hate resizing all my pics I'd start a thread.
- Mon Aug 28, 2023 11:52 pm
- Jump to forum
- Jump to topic
- Tue Aug 29, 2023 3:09 pm
- Jump to forum
- Jump to topic
Re: Graupner/Mugen Mercury CAD model...
WHile awaiting the part for other projects, I restarted to work on this Mugen Mercury... https://i.imgur.com/uii55qU.jpg The chassis is quite complex to measure for multiple reasons : it has everything to make it difficult : - plans are not parallel - length is too long for my caliper - and each cur...
- Fri Sep 01, 2023 5:39 am
- Jump to forum
- Jump to topic
Re: So what did you get in the post today ???
Printed parts for my special project arrived today...
Eager to see the week-end starting...
Eager to see the week-end starting...
- Sat Sep 02, 2023 3:36 pm
- Jump to forum
- Jump to topic
Re: Dadio's 3D Printing Stuff
All my nylons and PC are in sealed dry boxes with silica packs in and with bowdan tubes to the printer , as you say you get a few months before drying again , I don't really bother with PLA other than having it in large tubs with silica packs but not that well sealed . The Mini Mustang is coming alo...
- Thu Sep 07, 2023 11:07 pm
- Jump to forum
- Jump to topic
Re: ** Build of the Month Contest - September 2023 * - Winner - RC10resto
20230909_185740.jpg 33 Ford on a carbon chassis. Savox SC-0251mg servo and a Intellispeed mild-mod ESC. Velcro body and grill mounts. Axial 20T motor for easy street runs on soft foams. Aluminum rear axle and hubs that are spaced for stance. Original brass bushings in the rear. Full bearings up fro...
- Wed Sep 13, 2023 7:59 pm
- Jump to forum
- Jump to topic
Re: So, what did you do RC today?
After a couple of weeks of searching for 2.5" wide rubber drag slicks unsuccessfully, I decided to try to make my own. And after looking further into the originals I was looking for, that is exactly what the manufacturer did! They basically had their sidewalls, and they retreaded the top with a...