Resurrecting my goldpan

General discussion, builds/restorations, etc...

Moderators: scr8p, klavy69

AVguy
Approved Member
Posts: 45
Joined: Sat Jan 23, 2021 8:01 pm
Location: Westchester, New York
Been thanked: 9 times

Re: Resurrecting my goldpan

Post by AVguy »

TheDiamondOne wrote: Sat Feb 13, 2021 5:51 am https://www.amazon.com/Charger-Battery-Balance-Discharger-Li-ion/dp/B08C592PNV

Also, u can set cutoff voltage to auto or 3.0v per cell in esc and run it till it suts off with no worries.
Good to know. I’ll see about programming that. Thanks!
When will then be now?
Soon.

AVguy
Approved Member
Posts: 45
Joined: Sat Jan 23, 2021 8:01 pm
Location: Westchester, New York
Been thanked: 9 times

Re: Resurrecting my goldpan

Post by AVguy »

coxbros1 wrote: Sat Feb 13, 2021 5:29 am
AVguy wrote: Fri Feb 12, 2021 11:02 pm
juicedcoupe wrote: Fri Feb 12, 2021 9:17 pm If the battery is below the low voltage threshold, most lipo chargers will not start.

This is something I've done in the past, however some may not agree with it. I hooked the lipo battery up to my old nicd quick charger for about 5 minutes. This raised the voltage of the pack up above the lipo charger's threshold and allowed the pack to be charged.

Do I need to buy a new charger or can I get by without it?
If not, any recommendations for one that won’t break the bank?
This is ac/dc, 10amp, has all the protection features....just what the doctor ordered, plus it will keep u from burning down your house, lipos can be scary

https://www.ebay.com/itm/293945415354
Thanks, I think I’ll check out that charger. It took almost 2 hours to charge the battery with my 3amp charger.
When will then be now?
Soon.

User avatar
coxbros1
Super Member
Posts: 2187
Joined: Mon Dec 24, 2018 8:50 am
Location: Energy, Illinois
Has thanked: 1975 times
Been thanked: 1756 times

Re: Resurrecting my goldpan

Post by coxbros1 »

Tap pic for clarity: Derek

AVguy
Approved Member
Posts: 45
Joined: Sat Jan 23, 2021 8:01 pm
Location: Westchester, New York
Been thanked: 9 times

Re: Resurrecting my goldpan

Post by AVguy »

When will then be now?
Soon.

AVguy
Approved Member
Posts: 45
Joined: Sat Jan 23, 2021 8:01 pm
Location: Westchester, New York
Been thanked: 9 times

Re: Resurrecting my goldpan

Post by AVguy »

Wow this thing is fast! I haven’t taken it outside yet because the roads are filled with salt and I don’t want to get my car dirty. Also, I haven’t finished the body yet. I’ve been driving it around the basement and doing burnouts. When I gun it, this thing takes off like a rocket. Only problem now is the motor spins the wheels right off the tires.
I’m using J Concepts double dees tires on the rear with my old three piece wheels (actually two piece because I’m not using the plastic insert). I assumed from my research that these tires fit these rims but maybe not.
I’d rather not glue them on these wheels so I guess I need new wheels. The J Concepts hazard wheels look cool. Are there other wheels that will fit this car without changing the hub?
Attachments
9D78B22A-5525-480B-B9EF-3EF91375D1FC.jpeg
05A837A2-B03C-4E95-A4A2-A2AEE6F8EB22.jpeg
When will then be now?
Soon.

User avatar
juicedcoupe
Super Member
Posts: 2989
Joined: Sun Aug 16, 2020 4:05 pm
Location: Pascagoula, MS
Has thanked: 231 times
Been thanked: 1747 times

Re: Resurrecting my goldpan

Post by juicedcoupe »

https://www.rc10talk.com/viewtopic.php?f=35&t=45606

See the parts about cars with 1/4" axles.

Jconcepts front wheels and Traxxas rear wheels with Factory Works hexes.
Always looking for new and interesting ways to waste money.

AVguy
Approved Member
Posts: 45
Joined: Sat Jan 23, 2021 8:01 pm
Location: Westchester, New York
Been thanked: 9 times

Re: Resurrecting my goldpan

Post by AVguy »

juicedcoupe wrote: Sun Feb 14, 2021 8:11 pm https://www.rc10talk.com/viewtopic.php?f=35&t=45606

See the parts about cars with 1/4" axles.

Jconcepts front wheels and Traxxas rear wheels with Factory Works hexes.
Thanks that’s helpful. I also saw someone in that thread mention JC Racing so I checked out their website. I really liked the 5 spoke wheels. I guess I have some more ordering to do. It’s just too bad I bought two sets of the JConcepts tires (front and back). Maybe I’ll get the hazard wheels too.
When will then be now?
Soon.

User avatar
juicedcoupe
Super Member
Posts: 2989
Joined: Sun Aug 16, 2020 4:05 pm
Location: Pascagoula, MS
Has thanked: 231 times
Been thanked: 1747 times

Re: Resurrecting my goldpan

Post by juicedcoupe »

I like the Hazzard wheels as well, I have three sets. Be careful though, as their matching tires are about the only thing I've found that fits them well. Their availability seems to go in spurts.
Always looking for new and interesting ways to waste money.

AVguy
Approved Member
Posts: 45
Joined: Sat Jan 23, 2021 8:01 pm
Location: Westchester, New York
Been thanked: 9 times

Re: Resurrecting my goldpan

Post by AVguy »

Right now I can only find the Hazard rear wheels in black and front wheels in white. Rest is backordered. I think I’ll get a set in black and white since I have the wheels. I’m ordering the J concepts and the traxxas wheels with the hex adapter on eBay.
Can I use any 2.2” 1/10 buggy tires on these wheels? I searched on eBay and found tires from duratrax, pro line and Schumacher.
When will then be now?
Soon.

User avatar
juicedcoupe
Super Member
Posts: 2989
Joined: Sun Aug 16, 2020 4:05 pm
Location: Pascagoula, MS
Has thanked: 231 times
Been thanked: 1747 times

Re: Resurrecting my goldpan

Post by juicedcoupe »

AVguy wrote: Tue Feb 16, 2021 12:30 am I’m ordering the J concepts and the traxxas wheels with the hex adapter on eBay.
Can I use any 2.2” 1/10 buggy tires on these wheels? I searched on eBay and found tires from duratrax, pro line and Schumacher.
Just to be clear, the wheels from the link. Yes, they are standard 2.2 buggy tires. Several manufacturers make all different types to choose from.
Always looking for new and interesting ways to waste money.

AVguy
Approved Member
Posts: 45
Joined: Sat Jan 23, 2021 8:01 pm
Location: Westchester, New York
Been thanked: 9 times

Re: Resurrecting my goldpan

Post by AVguy »

juicedcoupe wrote: Tue Feb 16, 2021 1:17 am
AVguy wrote: Tue Feb 16, 2021 12:30 am I’m ordering the J concepts and the traxxas wheels with the hex adapter on eBay.
Can I use any 2.2” 1/10 buggy tires on these wheels? I searched on eBay and found tires from duratrax, pro line and Schumacher.
Just to be clear, the wheels from the link. Yes, they are standard 2.2 buggy tires. Several manufacturers make all different types to choose from.
Yes, the wheels from the link. Time to go shopping.
When will then be now?
Soon.

mikea96
Super Member
Posts: 3304
Joined: Thu Oct 01, 2009 4:34 pm
Location: Puyallup, WA
Has thanked: 189 times
Been thanked: 594 times

Re: Resurrecting my goldpan

Post by mikea96 »

You can't use 2.2 tires on then Jconcepts hazard wheels those are smaller wheels.

AVguy
Approved Member
Posts: 45
Joined: Sat Jan 23, 2021 8:01 pm
Location: Westchester, New York
Been thanked: 9 times

Re: Resurrecting my goldpan

Post by AVguy »

mikea96 wrote: Tue Feb 16, 2021 1:33 am You can't use 2.2 tires on then Jconcepts hazard wheels those are smaller wheels.
Right. The link was for the J Concepts mono front wheels and the traxxas 7171 for the rears with the hex adapters.
I had ordered J Concepts hazard tires for use with my old three piece wheels. I didn’t want to glue them so I also want to order the hazard wheels to go with them.
I also like the jc racing 5 star wheels. I’m gonna have so many freakin’ wheels.
When will then be now?
Soon.

AVguy
Approved Member
Posts: 45
Joined: Sat Jan 23, 2021 8:01 pm
Location: Westchester, New York
Been thanked: 9 times

Re: Resurrecting my goldpan

Post by AVguy »

Are there any tires that will work with the old three piece wheels without glueing?
When will then be now?
Soon.

User avatar
TRX-1-3
Super Member
Posts: 1743
Joined: Sat Mar 29, 2014 12:13 pm
Location: USAG Humphreys, South Korea
Has thanked: 1399 times
Been thanked: 764 times

Re: Resurrecting my goldpan

Post by TRX-1-3 »

Aren't the old three piece beadlocks?
Hope you're doin' something fun.

Post Reply

Create an account or sign in to join the discussion

You need to be a member in order to post a reply

Create an account

Not a member? register to join our community
Members can start their own topics & subscribe to topics
It’s free and only takes a minute

Register

Sign in

  • Similar Topics
    Replies
    Views
    Last post
  • Resurrecting my Houge RC10
    by ovalRC89 » » in RC10 Buggy Forum
    20 Replies
    2594 Views
    Last post by ovalRC89
  • Resurrecting my old dirt oval for my son hopefully!?
    by cc4x4 » » in RC10 Buggy Forum
    1 Replies
    733 Views
    Last post by tuna.Rc
  • Resurrecting/Modernizing Your Vintage R/C's Electronics
    by scr8p » » in Modern Electronics
    90 Replies
    39802 Views
    Last post by bigrobbyt
  • Resurrecting my car and making it a Bad A$$
    by Zmd73 » » in RC10 Buggy Forum
    17 Replies
    2247 Views
    Last post by JK Racing
  • My Goldpan
    by craigc8791 » » in RC10 Buggy Forum
    4 Replies
    615 Views
    Last post by Charlie don't surf
  • Project Goldpan
    by vintage AE » » in RC10 Buggy Forum
    15 Replies
    3324 Views
    Last post by vintage AE
  • Goldpan DS conversion
    by JosephS » » in Associated On-Road Forum
    20 Replies
    1195 Views
    Last post by JosephS
  • My First Goldpan... Ideas?
    by spydur23 » » in RC10 Buggy Forum
    1 Replies
    621 Views
    Last post by 85Edinger

Return to “RC10 Buggy Forum”

Who is online

Users browsing this forum: No registered users and 43 guests